Function Selection - Mitsubishi Electric CITY MULTI PAR-21MAA Manual De Instalación

6 Set the address of the LOSSNAY you want to register using the [
(01 to 50)
7 Press the [TEST] button, and register the set indoor unit address and
LOSSNAY address.
- Registration end display
The indoor unit address and "IC" and LOSSNAY address and "LC"
are alternately displayed.
- Registration error display
If the address was not correctly registered, the indoor unit address
and registered LOSSNAY address are alternately displayed.
Cannot be registered because the registered indoor unit or LOSSNAY does not exist.
Cannot be registered because another LOSSNAY was registered at the registered indoor unit.
< 2. Confirmation procedure >
8 Set the address of the indoor unit connected by the remote controller whose LOSSNAY you want to
confirm using the [ TEMP. (
9 Press the [ MENU] button and confirm the LOSSNAY address reg-
istered at the set indoor unit address.
- Confirmation end display (When LOSSNAY is connected.)
The indoor unit address and "IC" and registered LOSSNAY address
and "LC" are alternately displayed.
- Confirmation end display (When LOSSNAY is not connected.)
Registered indoor unit address does not exist.
< 3. Deletion procedure >
Use this procedure when you want to delete registration of indoor units connected by the remote controller and LOSSNAY.
; Confirm (see 2. Confirmation procedure) the LOSSNAY you want
to delete and display the indoor units and LOSSNAY confirmation
results.
A Press the [ ON/OFF] button twice and delete registration of the
LOSSNAY registered at the set indoor unit.
- Deletion end display
Indoor unit address and "– –" and registered LOSSNAY address
and "– –" are alternately displayed.
- Deletion error display
When deletion was not performed properly.
6

Function Selection

(1) Function selection of remote controller
The setting of the following remote controller functions can be changed using the remote controller function selection mode. Change the setting
when needed.
Item 1
1. Change Language Language setting to display
("CHANGE LANGUAGE")
2. Function limit (1) Operation function limit setting (operation lock) ("LOCKING FUNCTION")
("FUNCTION SELEC- (2) Use of automatic mode setting ("SELECT AUTO MODE")
TION") (3) Temperature range limit setting ("LIMIT TEMP FUNCTION")
(4) Use of automatic filter elevation panel up/down operation mode setting
(5) Use of fixed airflow direction mode setting
(1) Remote controller main/sub setting ("CONTROLLER MAIN/SUB")
3. Mode selection
("MODE SELECTION")
(2) Use of clock setting ("CLOCK")
(3) Timer function setting ("WEEKLY TIMER")
(4) Contact number setting for error situation ("CALL.")
(1) Temperature display °C/°F setting ("TEMP MODE °C/°F")
4. Display change
(2) Suction air temperature display setting ("ROOM TEMP DISP SELECT")
("DISP MODE SETTING")
(3) Automatic cooling/heating display setting ("AUTO MODE DISP C/H")
) and ( )] buttons. (01 to 50)
Item 2
CLOCK ( ) and ( )] buttons.
• Display in multiple languages is possible.
• Setting the range of operation limit (operation lock)
• Setting the use or non-use of "automatic" operation mode
• Setting the temperature adjustable range (maximum, minimum)
• Setting the use or non-use of the automatic filter elevation panel up/down operation mode
• Setting the use or non-use of the fixed airflow direction mode
• Selecting main or sub remote controller
* When two remote controllers are connected to one group, one controller must be set to sub.
• Setting the use or non-use of clock function
• Setting the timer type
• Contact number display in case of error
• Setting the telephone number
• Setting the temperature unit (°C or °F) to display
• Setting the use or non-use of the display of indoor (suction) air temperature
• Setting the use or non-use of the display of "Cooling" or "Heating" display during operation
with automatic mode
Indoor unit address LOSSNAY address
<Indoor unit address>
Item 3 (Setting content)
4