Maintenance; Resetting The Motor Thermostat - Shark NV22L Manual Del Usuario

Maintenance

Maintenance

Resetting the Motor Thermostat

Resetting the Motor Thermostat
Your Shark Your Shark ® ® Upright Vacuum is equipped Upright Vacuum is equipped
with a protective Motor Thermostat. with a protective Motor Thermostat.
If the motor should overheat, the If the motor should overheat, the
thermostat shuts off the power. thermostat shuts off the power.
To reset the Motor Thermostat: To reset the Motor Thermostat: Wait 45 minutes for vacuum to cool; Wait 45 minutes for vacuum to cool;
then plug in the vacuum. then plug in the vacuum.
Move the Power Button to the Move the Power Button to the
"O – Off" position. "O – Off" position. Turn the Power Switch to the "I – On" Turn the Power Switch to the "I – On"
position to start the vacuum. position to start the vacuum.
Unplug the vacuum. Unplug the vacuum.
Note: if vacuum still does not start, Note: if vacuum still does not start,
Check for clogged hose or filter; unclog Check for clogged hose or filter; unclog
contact Customer Service at: contact Customer Service at:
hose and replace filter. Refer to hose and replace filter. Refer to
1-800-798-7398. 1-800-798-7398.
Checking for Blockages on page13. Checking for Blockages on page13.
14 14
14 TOLL FREE: 1-800-798-7398
NV22L_IB_100204.indd 14-15
A A
1 1 2 2
Cleaning the Pet Hair Cleaning the Pet Hair Cleaning the Pet Hair Cleaning the Pet Hair
Power Brush - Models NV22L, Power Brush - Models NV22L, Power Brush - Model NV22LWM Power Brush - Model NV22LWM
NV22LB, NV22LC, NV22LCO, NV22LB, NV22LC, NV22LCO,
Turn the Turbo Brush over and slide Turn the Turbo Brush over and slide
NV22W NV22W
locking latch (B) forward. locking latch (B) forward.
Slide locking latch (A) forward. Slide locking latch (A) forward.
Gently tilt brush housing upward Gently tilt brush housing upward
Gently tilt brush housing upward Gently tilt brush housing upward to open. to open.
to open. to open.
Remove debris from turbine wheel Remove debris from turbine wheel
IMPORTANT: DO NOT force; it will IMPORTANT: DO NOT force; it will and air passage. and air passage.
not open all the way. not open all the way.
To reassemble, insert the tabs on To reassemble, insert the tabs on
Remove debris from turbine wheel Remove debris from turbine wheel the front edge of the cover into the the front edge of the cover into the
and air passage. and air passage. matching holes in the top half and tilt matching holes in the top half and tilt
the cover back down until it clicks into the cover back down until it clicks into
place. place.
Ordering Replacement Parts Ordering Replacement Parts
Part Part
To order additional parts and accessories, To order additional parts and accessories,
Super Stretch Hose Super Stretch Hose
go to www.sharkclean.com or call go to www.sharkclean.com or call
1-800-798-7398. Note: some parts 1-800-798-7398. Note: some parts
Dusting Brush & Crevice Tool 1115-FC Dusting Brush & Crevice Tool 1115-FC
may be available at your local Shark may be available at your local Shark ® ®
Foam & Felt Filters Foam & Felt Filters
retailer. retailer.
Turbo brush (1), Turbo brush (1),
Turbo brush (2), Turbo brush (2),
Cleaning Wand Cleaning Wand
24"Crevice Tool 24"Crevice Tool
B B
Part No. Part No.
1114-FC 1114-FC
XF22 XF22
1117-FC 1117-FC
1144-FC 1144-FC
1116-FC 1116-FC
1124-FC 1124-FC
15 15
www.sharkclean.com
English
15
10-02-08 8:49 AM