Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
REMEMBER: You must reset the hair length
selector back to your desired setting every time
you replace the comb on the appliance.
The remaining hair length corresponds with
the smallest distance between the cutting
blade and the spot where the comb is in contact
with the skin.
Beard Trimming Without Beard Comb
Remove comb if you are:
Defining hair lines
Trimming nape of neck
Removing single, unwanted hairs
1
Be certain the Groomer is in the OFF
position.
2
Remove the comb by pressing the Hair
Length Setting Selector (1) and slide the
comb upwards (2). Pull comb off Groomer .
3
Turn the Groomer ON (fig. 5).
4
Make well-controlled movements. Touch the
hair/skin lightly with the Groomer.
Styling/Contouring with Precision
Trimmer
Use the precision trimmer to cut shapes in
beard hair or scalp hair.
B e careful when using the precision trimmer as
it removes every hair it touches.
1
Put the precision trimmer on the Groomer
handle (1) and turn clockwise (2) (fig. 20).
2
Make careful and controlled movements with
the precision trimmer.
3
For best results, move the precision trimmer
against the direction of hair growth making
sure it is in full contact with the skin (fig. 21).
Grooming Nose/Ear Hair
1
Be certain the Groomer is in the OFF
position.
2
Remove the trimmer by turning counter-
clockwise and pulling it off the Groomer
handle.
3
Put the nose trimmer on the Groomer
handle (1) and turn clockwise (2) (fig. 22).
Trimming Nose Hair
Make sure nasal passages are clean.
Put the nose trimmer on the Groomer
1
handle (1) and turn clockwise (2) (fig. 22).
2
Turn the Groomer ON and insert the tip
of the attachment into one nostril (fig. 23).
CAUTION: Do Not insert the tip more
than 3/16 in./5mm into your nostril.
Slowly move the tip in and out while
3
turning it around at the same time in order
to remove unwanted hair. For best results,
make sure the side of the tip is firm against
skin. This will reduce the tickling effect that
can occur during trimming of nose hair.
4
Turn off Groomer. Rinse attachment clean
after each use.
Trimming Ear Hair
Clean outer area of ear and ear canal. Make
sure it is free of wax.
Nose trimmer should be on the Groomer.
1
Turn the Groomer ON and move the tip
softly around the edge of ear to remove hairs
extending beyond the outer ear (fig. 24).
2
Carefully insert the tip into outer ear canal
(fig. 25).
CAUTION: Do not insert the tip further
than 3/16 in./5mm into the ear as this
could cause damage to the eardrum.
3
Turn off Groomer. Rinse attachment clean
after each use.
Cleaning
Clean the attachments after each use.
Always switch Groomer OFF, unplug
and remove power supply cord from
Groomer before cleaning.
Do not use compressed air, abrasive cleaning
agents, scourers or liquids such as alcohol,
benzene, bleach or acetone to clean the
Groomer and attachments.
Never clean, replace or remove Groomer
attachments with motor ON.
Do not apply pressure to cutters.
Do not touch cutters with hard objects as this
may damage them.
During Use:
If cut hairs have accumulated in the comb area,
remove hairs by shaking or blowing. Remember
to adjust the trimming length back to your
selected setting when you replace the comb on
Groomer.
After Each Use:
1
Make sure the Groomer is switched OFF
and disconnected from the electrical outlet.
2
Remove any comb or attachment.
3
Blow and/or shake out any hair that may
have accumulated in the comb or attachment.
4
Rinse combs, attachments and appliance
under warm tap water.
5
Shake excess water from combs and
attachments and allow to air dry thoroughly.
6
Place the attachment back on the Groomer
handle.
NOTE: To maintain optimal trimming
performance, lubricate the teeth of the full-size
metal trimmer, the detail trimmer and the nose
trimmer with a few drops of oil from the bottle
supplied every three months and after cleaning
(fig. 26).
Cleaning the Body Shaver
Pull the shaving unit out of the body shaver
1
(fig. 27).
2
Blow and/or shake out any hair that may have
accumulated inside the body shaver (fig. 28).
3
Clean the body shaver and shaving unit
under warm tap water (fig 29).
The shaving foil is very delicate and should not
be handled.
If foil becomes damaged, do not continue
using the body shaver. Do not apply pressure
to shaving foil.
4
Shake excess water from body shaver and
shaving unit and allow to air dry thoroughly.
Do not use a towel to dry the shaving unit as
damage could occur.
5
Apply a drop of oil from the bottle supplied
to the foil every three months and after
cleaning.
Replacing the Bodygroom Shaver
Shaving Foil Head
If the shaving unit is worn or damaged, do not
continue using the Bodygroom shaver. Replace
the shaving unit immediately.
It is recommended that you replace your
shaving unit once a year.
A worn or damaged shaving unit should only
be replaced with an original Philips Norelco
shaving foil, model BG2000, which is
available on the Philips Norelco website,
www.philips.com/support or call
1-800-243-3050 for assistance.
The foil is a precision part. Handle with care.
1
Always switch Groomer OFF and remove
Groomer plug from outlet before
replacing shaving unit.
2
Remove the shaving unit head by pulling it off
the appliance.
3
Place the new shaving unit head on the
Groomer by snapping it into place.
You will hear a "click".
After replacing the shaving unit head, check that
the shaving head is firmly attached before using
Groomer.
This Groomer has no other user-serviceable
parts. For assistance call 1-800-243-3050.
Storage
Be sure Groomer is turned OFF. Remove cord
from outlet and Groomer before storing in a
safe, dry location where it will not be crushed,
banged, or subject to damage.
Store the Groomer and attachments in the
pouch to prevent damage.
Do not wrap cord around Groomer when
storing.
Store cord in a safe location where it will not
be cut or damaged.
Do not place or store Groomer where it can
fall or be pulled into a tub or sink, water or
other liquid while plugged in.
Publicidad
Tabla de contenido
