Replacing The Power Cable; Cleaning, Maintenance And Ordering Of Spare Parts; Carbon Brushes; Disposal And Recycling - EINHELL GC-EL 2500 E Manual De Instrucciones

6.4 Emptying the debris bag and pre-screen
(Fig. 1)
Empty the debris bag (7) in good time. When
the bag is heavily loaded with material, vacuum
power is considerably reduced. Deposit organic
refuse at a compost site.
•
Switch off the tool and pull out the plug.
•
Open the zipper on the debris bag (7) and
shake out the material.
•
Close the zip on the debris bag (7) again.
6.5 Speed control (Fig. 1)
The device is fi tted with an electronic speed con-
troller. To use it, turn the speed controller (Fig. 1/
Item 10) to the desired position. Use the device
only with the speed which is actually required and
do not let it run at a speed which is faster than
necessary.

7. Replacing the power cable

Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
authorized after-sales service or similarly trained
personnel to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
•
After shaking out the debris bag, turn it inside
Anl_SA_GC_EL_2500_E_SPK8.indb 22 Anl_SA_GC_EL_2500_E_SPK8.indb 22
GB
out and thoroughly clean it in order to prevent
mould and unpleasant odors from forming.
•
You can use soap and water to clean out a
heavily soiled debris bag.
•
Rub a bar of dry soap across the zipper teeth
if the zipper becomes difficult to pull.
•
Clean the vacuum/blower tube with a brush
upon evidence of dirt and grime.
•
Dirt and grime can make the switch (blower/
vacuum) more difficult to operate as a result
of the material that swirls up off the ground.
When this occurs, simply flip the switch back
and forth a few times, which should bring it
back to the normal feel.

8.2 Carbon brushes

In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician
and/or an authorized service agent.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician or the
authorized service technician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required

9. Disposal and recycling

The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council offi ces.
- 22 -
05.12.2016 10:55:50 05.12.2016 10:55:50