Before Using The Equipment - EINHELL VENTURRO 18/210 Manual De Instrucciones Original

mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
4. Risk of eye damage if suitable safety goggles
are not worn.
This equipment generates an electromagnetic
fi eld during operation. Under certain circumstan-
ces this fi eld may actively or passively impede
medical implants. To reduce the risk of serious
or fatal injuries, we recommend persons with
medical implants to consult their doctor and the
manufacturer of the medical implant prior to using
the equipment.

5. Before using the equipment

The equipment is supplied without batteries
and without a charger.
Warning!
Always remove the batteries before making
adjustments to the equipment.
5.1 Preparations
5.1.1 Suction tube
Connect the top suction tube (Fig. 3a/Item 6) and
the bottom suction tube (Fig. 3a/Item 8) together.
Make sure that the guide lug (Fig. 3a/Item A) is in-
serted into the corresponding recess (Fig. 3a/Item
B) when you do this. Make sure that it latches in
place correctly as well.
Screw the two tubes together in addition with the
tapping screw (Fig. 3b/Item 7). Now slide the fully
assembled suction tube into the motor housing
(Fig. 4a) and secure it with the two star screws
(Fig. 4b/Item 4).
Important!
Please note that the two suction tubes must al-
ways be joined together before they are mounted
on the motor housing, and that they must then
never be taken apart again.
Integrated safety switches will be pressed and the
machine supplied with voltage only after the fully
assembled suction tube has been properly scre-
wed to the motor housing .
Anl_Venturro_18_210_SPK13.indb 19 Anl_Venturro_18_210_SPK13.indb 19
GB
5.2 Fitting the wall bracket
Push the wall bracket (Fig. 5a / Item 11) onto the
motor housing (Fig. 5b) as far as the stop. Make
sure that the V-shaped cut-out (Fig. 5b / Item 11a)
faces the suction tube in order to be able to hang
the machine from a screw in the wall. The wall
bracket also serves as a support when the machi-
ne is placed on the ground.
5.3 Fitting the harness
Pull back the catch (Fig. 6 / Item 5a) of the carabi-
ner and hook it on the motor housing (Fig. 6).
5.4 Fitting / removing the catch bag
•
Slip the catch bag connection (Fig. 2 / Item
10a) over the mount (Fig. 7a / Item 10b) on
the motor housing. Make sure that it latches
in place correctly (Fig. 7b).
•
Hook the catch bag on the suction tube in
one of the two holes (Fig. 7c / Item 8a/8b)
(Fig. 7d). The hole (Fig. 7c / Item 8c) cannot
be used on this model.
To remove the catch bag, unhook it from the suc-
tion tube. Press the release levers (Fig. 7b / Item
10c) simultaneously on the left and right and pull
off the catch bag.
5.5 Fitting the battery
Press the pushlock button (Item C) of the rechar-
geable battery as shown in Fig. 8a and push the
battery into the battery mount provided until it
latches in place. Fig. 8b shows the rechargeable
batteries when fi tted. To remove the battery pack,
proceed in reverse order.
5.6 Charging the battery
1. Take the battery pack out of the equipment.
To do so, press the pushlock button (Fig. 8a/
Item C).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
into the socket outlet. The green LED will then
begin to fl ash.
3. Insert the battery pack into the charger (Fig.
9).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The rechargeable battery can become a little
warm during the charging. This is normal.
- 19 -
13.01.2022 14:32:41 13.01.2022 14:32:41