Before Starting The Equipment; Safety Switch - EINHELL GE-CL 36/230 Li E Manual De Instrucciones Original

1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear
protection is applied.
3. Health damage caused by hand-arm
vibrations if the equipment is used over a
longer period or is not properly guided and
maintained.
4. Risk of eye damage if suitable safety goggles
are not worn.
This equipment generates an electromagnetic
fi eld during operation. Under certain
circumstances this fi eld may actively or passively
impede medical implants. To reduce the risk of
serious or fatal injuries, we recommend persons
with medical implants to consult their doctor and
the manufacturer of the medical implant prior to
using the equipment.

5. Before starting the equipment

Warning!
Always remove the batteries before making
adjustments to the equipment.
5.1 Preparations (Fig. 4-9)
5.1.1 Suction tube
Connect the top suction tube (Fig. 4/Item 2) and
the bottom suction tube (Fig. 4/Item 1) together.
Make sure that the guide lug (Fig. 4/Item 13)
is inserted into the corresponding recess (Fig.
4/Item 14). Make sure that it latches in place
correctly as well. Use the suction tube only if it is
fully assembled. Push the guide wheels (Fig. 5/
Item 9) onto the bottom suction tube (Fig. 5/Item
1), as shown in Fig. 5, with the lock pressed (Fig.
5/Item 15) and let them snap into place at the
desired position. The position can be changed
at any time by pressing the lock again. Make
sure that it snaps into place correctly. Fit the
additional handle (Fig. 6/Item 3) to the mount on
the top suction tube (Fig. 6/Item 2). Using the
screw (Fig. 7/Item 11) and the star nut (Fig. 8/Item
12), secure the additional handle in the desired
position. When fi tting the screw, make sure that
you insert it from the side with the hexagon lock
(Fig. 7/Item 27) provided for the purpose. The
position can be changed at any time by undoing
the star nut. Make sure that the parts are fastened
securely.
Anl_GE_CL_36_230_Li_E_SPK7_USA.indb 12
EN
5.1.2 Blower tube
Pull the sleeve (Fig. 9/Item 16) to the top end of
the blower tube (Fig. 9/Item 8) as shown in Fig. 9.
Make sure that it snaps in place correctly on both
sides.
5.2 Assembly in blower mode (Fig. 10-11)
Insert the blower tube (Fig. 10/Item 8), which was
prepared in 5.1, into the mount (Fig. 10/Item 17)
on the motor housing. Make sure that it latches
in place correctly. Attach the harness (Item 4)
to the motor housing as shown in Fig. 11. The
equipment has now been assembled in blower
mode (Fig. 1). To dismantle, proceed in reverse
order. To remove the blower tube, press the button
(Fig. 10/Item 18) and pull off the blower tube.
5.3 Assembly in vacuum mode (Fig. 12-17)
Undo the star screw (Fig. 12/Item 19) and pull
open the cover (Fig. 12/Item 20). Attach the
vacuum tube (Fig. 13/Item 2), which was prepared
in 5.1.1, to the motor housing and snap it onto
the motor housing as shown in Fig. 13. Now
secure it with the thumb screw (Fig. 14/Item 21).
Attach the harness (Item 4) to the motor housing
as shown in Fig. 15. Connect the catch bag (Fig.
16/Item 7) to the mount (Fig. 16/Item 22) on the
motor housing. Make sure that it latches in place
correctly. Secure the catch bag by the two hooks
on the vacuum tube as shown in Fig. 17.
The equipment has now been assembled in
vacuum mode (Fig. 2). To remove the catch bag,
press the button (Fig. 16/Item 18) and pull off
the catch bag. To dismantle the rest, proceed in
reverse order to assembly. Start up the equipment
only when fully assembled.

5.4 Safety switch

There are a number of safety switches for
preventing the unsafe operation of the equipment.
Make sure, therefore, that the following
components are correctly fastened, otherwise it
will not be possible to switch on the machine.
•
In blower mode: Blower tube (Fig. 10/Item 8)
and cover (Fig. 12/Item 20).
•
In vacuum mode: Suction tube (Fig. 14/Item
2) and catch bag (Fig. 16/Item 7)
5.5 Fitting the battery (Fig. 18-20)
Press the pushlock button (Fig. 20/Item 25) of
the rechargeable battery as shown in Fig. 20
and push the battery into the battery mount
provided until it latches in place. Fig. 19 shows the
rechargeable batteries when fi tted. To remove the
battery pack, proceed in reverse order.
- 12 -
08.07.2020 11:25:23