Main Menu - Televes Avant3 Manual De Instrucciones

Ocultar thumbs Ver también para Avant3:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Launch Amplifier Avant3

Main menu

From this time, press shortly the
the main menu in the following sequence: Inputs,
Filter 1, ..., Filter 5, and Filter VHF.
Remark:
To change the interface language before
starting the configuration of the device, you
must access the language menu. To do so,
press the
menu to access the Extended menu, and then,
FILTRO 1
using the keys
LTRO 1
Finally, press the
__
changes.
For more information, see section Extended
Menu => Language selection.
FILTRO 1
FILTRO 1
LTRO 1
_ _
25 __
__
__
Configuration of inputs
FILTRO 1
The first menu displayed is the "Inputs menu. "
LTRO 1
FILTRO 1
The mapping of the keys in this menu is:
_
25
_
_ _
&
Scroll through the menu options: 5-0,
28
25 __
2-3.
(Short press) - Positions the cursor over
each modifiable parameter.
FILTRO 2
Error F1
(Long press) - Calls the extended menu
FILTRO 1
LTRO 2
_
(language).
Error F1
27
_
_
(Short press) - Shifts to the next main
_
25
28
menu.
31
(Long press) - Recording of parameters.
FILTRO 2
To change the value selected with the cursor, you
Error F1
must press the key
_
_
flashing. Next, change its value directly by
27
31
keys.
key to scroll
key (long press) from the Input
or
, select the language.
FILTRO 1
key (long press) to save the
__
FILTRE 1
FILTRO 1
_ _
__
25 __
FILTRO 1
FILTRE 1
_
28
_
_
_ _
25
28
25 __
FILTRE 1
FILTRO 2
_
Error F1
31
_
_
_
25
27
31
FILTRE 2
Error F1
then that value will start
_
27
Programming of filters
Pressing the
Programming Filters. The mapping of the keys in
this menu is:
Selection of upper and lower channel filter.
(Short press) - Positioning of the cursor.
(Long press) - Not applicable
(Short press) - Moves to the next menu.
(Long press) - Recording of parameters.
FILTRE 1
FILTRE 1
__
__
FILTRE 1
Press the
channel of Filter 1. Use the keys
FILTER 1
FILTRE 1
_ _
select the lower channel of the filter. Press the
25 __
key (short press) to activate the upper channel of
_ _
__
25 __
the filter. Use the
channel of the filter.
FILTRE 1
FILTRE 1
FILTER 1
_
_
25
28
_
_ _
25 __
25
28
FILTRE 2
Above the channel value it can be seen a graphic
Error F1
FILTER 1
representation of the filter, which becomes wider
FILTRE 2
_
_
Error F1
as we increase the width of the filter.
27
31
_
_
_
Filters can be stretched up to 7 channels bandwidth,
28
25
27
31
from channel 30 onwards. If the lower end of
the filter is below the channel 31, the maximum
channel bandwidth is limited to 5 channels.
Modifying the lower end of the filter, automatically
FILTER 2
deletes its upper end.
The range of channels that can be entered is the
_
_
or
31
27
following:
UHF: --, 21, ..., 60
If there were overlapping of filters, the display
shows the filter which is in conflict and then the
unit is not able to record data.
key, you access the second menu,
FILTER 1
FILTER 1
__
__
FILTER 1
key (short press) to activate the first
SUODIN 1
FILTER 1
_ _
25 __
_ _
__
25 __
or
keys to select the upper
FILTER 1
FILTER 1
SUODIN 1
_
_
25
28
_
_
_ _
25
25 __
FILTER 2
Error F1
SUODIN 1
FILTER 2
_
_
Error F1
27
31
_
_
_
_
28
25
27
SUODIN 2
Error F1
_
_
31
27
SUODIN 1
SUOD
__
__
SUODIN 1
and
, to
SUOD
_ _
25 __
_ _
25 __
SUODIN 1
SUOD
_
_
25
28
_
_
28
25
SUODIN 2
Error F1
SUOD
_
_
Er
27
31
_
_
_
28
31
27
Error F1
_
31

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

532740Avant 3

Tabla de contenido