Publicidad
Idiomas disponibles
Idiomas disponibles
K. FUSE -
Protects the amplifier from electrical
fault. Replace a blown fuse only with the type and
rating specified on the rear panel of your amplifier. If
the amplifier repeatedly blows fuses, have it tested at
an authorized Fender
®
L. POWER - Switches the amplifier on and off.
M. POWER CORD - The power line cord must be
connected to a grounded AC receptacle in
compliance with the voltage and frequency ratings
specified on the rear panel of your amplifier.
N. STANDBY -
Use STANDBY instead of switching
POWER off during short breaks to avoid tube warm-
up
delay
and
Use STANDBY for 30 seconds when switching
POWER ON to extend tube life span.
TYPE:
PART NUMBERS:
POWER REQUIREMENT:
POWER OUTPUT:
IMPEDANCES
TUBES:
FUSE TYPE
SPEAKER COMPLEMENT:
OPTIONAL EXTENSION CABINET:
DIMENSIONS
WEIGHT:
w
w w
w w
w . . f f e
e n
n d
d e
Service Center.
related
tube
wear.
CSR 4
0811000000 (120V, 60Hz) USA
0811060000 (230V, 50Hz) EUR
195W
60W
INPUT 1: 1M ohms
Five 12AX7A (P/N 013341)
100V-120V UNITS: 3A, 250V
Three 8 ohm, 10 in ( 25.4 cm) Jensen
speakers (P/N 055613), total impedance 2.6 ohms
Vibro-King 212 enclosure with two 8 ohm, 12 in (30.7 cm) Celestion
Vintage 30 speakers (P/N 813-0400-010), total impedance 4 ohms
HEIGHT: 25.5 in (64.8 cm)
72 lb (32.7 kg)
Product specifications are subject to change without notice.
e r
r . . c
c o
o m
m
F F
F F
e e
e e
n n
n n
d d
d d
e e
e e
r r
r r
®
®
V V
V V
i i
i i
b b
b b
r r
r r
o o
o o
- -
- -
K K
K K
F F
F F
e e
e e
n n
n n
d d
d d
e e
e e
r r
r r
V V
V V
i i
i i
b b
b b
r r
r r
o o
o o
- -
- -
K K
K K
O.
ALWAYS connect one of three speaker
configurations to the amplifier before
switching the power on to prevent
damage to the amplifier:
P. FOOTSWITCH - Connect the footswitch (included)
to activate Vibrato and to enable remote ON/OFF
switching of Vibrato and FAT. When connected, the
footswitch overrides the FAT switch on the front
panel.
Q. EFFECTS RETURN/SEND - (1) Effects Loop -
Connect SEND to the input of your effects device
and the output of the effects device to RETURN.
(2) Multiple Amps - Connect SEND on the primary
unit to RETURN on the auxiliary unit. The primary
unit controls all auxiliary units.
(3) Recording or Reinforcement - Connect SEND
to the input jack of sound equipment.
S S
S S
0811030000 (240V, 50Hz) AUS
0811070000 (100V, 50Hz) JPN
INPUT 2: 136k ohms
Two GT–6L6 GE (P/N 059778)
230V-240V UNITS: 2.5A, 250V
®
reissue P10R
®
WIDTH: 24.75 in (62.9 cm)
w w
w
w w
w . . m
m r
r g
g e
i i
i i
n n
n n
g g
g g
™
™
C C
C C
u u
u u
s s
s s
t t
t t
o o
o o
m m
m m
i i
i i
n n
n n
g g
g g
C C
C C
u u
u u
s s
s s
t t
t t
o o
o o
m m
m m
MAIN/EXTERNAL SPEAKER -
The internal speakers.
The internal speakers and
a 4-ohm external speaker.
Two 4-ohm external speakers.
p p
e e
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
p p
e e
c c
i i
f f
i i
c c
a a
t t
i i
o o
n n
s s
0811040000 (230V, 50Hz) UK
OUTPUT: 2 ohms
One 6V6-GTA (P/N 023564)
DEPTH: 10.5 in (26.7 cm)
e a
a r
r h
h e
e a
a d
d . . n
7
n e
e t
t
Publicidad
