Vimar ELVOX 41016 Instrucciones Instalador página 6

Ocultar thumbs Ver también para ELVOX 41016:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 12
Fingerprint reader, 1 N/O relay output, to be
completed with front cover
1
Description
When a preconfigured print is recognised as valid, depending on
the pre-set fingerprint role, the device activates the "F1" local relay
output, to control the opening of a lock, for example.
The device has an input for a local button that, if enabled, can be
used to activate the F1 output directly.
Fingerprint programming is done with SaveProg or with installer
fingerprints, duly registered on the module.
The device can be installed with 41001, 41003, 41004 modules
in the Pixel series and in a stand-alone configuration, with a local
power supply of 5V.
2
Features
• Supply voltage: 5 Vdc from Audio-Video or Audio modules, via
a specific wiring harness, or from an additional power supply
unit, on the 5V+ and 5V- terminals.
• Absorption: 260 mA max
• Operating temperature: -25 °C / +55 °C.
• IP54 degree of protection
• Protection rating against impact IK08 (Pixel).
3
Terminals
• Local power supply (5 Vdc, 260 mA);
• "F1" output relay, NO (60 Vdc, 1A);
• Input for door command CA, NO.
4
Connections
• Connection to Pixel series modules.
• USB for configuration and updating
• RJ45, not used
5
Configuration.
The fingerprint programming is done firstly with SaveProg. 2 types
of user can be entered: installer or normal user. The installer fin-
gerprint is used for learning normal users, while the user finger-
print is used to recognise the behaviour configured during instal-
lation. In order to reduce the risk of malfunctions due to injuries
or other events, the installer should register at least 4 fingerprints
using the fingers on both hands: 2 with installer role and 2 with
user role. For the same reasons, for normal users at least 2 differ-
ent fingerprints should be recorded.
Up to 200 prints can be recorded (the sum of the user and installer
prints).
5.1 Management via SaveProg.
The print database can be configured via SaveProg.
In particular, you can:
• Set the operating mode as stand-alone or with audio/video
module;
• Add/Remove prints belonging to a user or installer.
6
• Change the fingerprint authorisations, from installer to user or
vice versa.
In the stand-alone configuration you can:
• Set the relay activation time.
• Enable the CA input for local relay opening.
In the configuration with AV module, F1 relay opening times and
CA enabling are set directly on the AV module.
Alongside a valid fingerprint, you can configure the AV module to
open the fingerprint reader module relay or one of those present
on the auxiliary modules, by configuring the AV module.
You can also configure the F1 relay as a common or exclusive
lock for the speech unit.
Connect the PC to the USB and follow the SaveProg instruction
documents for specific details.
In the event of an error, the function LEDs flash red. Make sure
that:
- the AV module is compatible with the fingerprint reader (e.g.
not item 41000);
- the fingerprint reader is communicating with the AV module
(incorrect wiring);
- the AV module firmware version is up to date.
5.1.1 Fingerprint configuration
To configure a fingerprint, select the type of print to be added from
the "Add fingerprint" keypad: User or Installer. Then click on "Add
fingerprint":
- with the blue status led and the green function leds flashing
intermittently, the device indicates the fingerprint check phase:
the user passes the finger once to check that the fingerprint is
not already in the database.
- if the finger is recorded, SaveProg gievs a message. Other-
wise the status led turns orange and the new fingerprint is
acquired. The finger must be pressed 3 times to complete the
operation.
The device indicates that the finger has been pressed cor-
rectly when the status led turns green for a few seconds.
Otherwise, if the acquisition is not successful the status led
turns red for a few seconds: the acquisition procedure must
be repeated.
- After all 3 acquisitions the status led and the 2 function leds
turn green for approximately 1 second.
- After acquisition SaveProg indicates that the operation was
successful and the device returns to normal operating model.
The status led remains blue.
5.2 Manual Management
You can also implement the following procedure to register a user
print:
1. Press a fingerprint programmed as "installer";
2. Within 5 s, press the print to be recorded as "user"; while
waiting the orange LED remains on.
3. To complete the fingerprint recording, the finger must be
pressed 3 times. When recorded correctly, the central LED
turns green for an instant. After all 3 acquisitions the central
led and the 2 leds below turn green for approximately 1 sec-
EN

Publicidad

Tabla de contenido
loading

Tabla de contenido