Descargar Imprimir esta página

Echo 99944300014 Hoja De Instrucciones

Kit de cuchillas trituradoras

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Subject:
Shredder Knives Kit
Kit:
99944300014
Model(s):
3" Chipper/Shredders (excluding SC-2013)
Before inspecting or servicing any part of this machine, shut off power source, disconnect the spark plug wire from the
spark plug, disconnect the battery cables (when applicable), and make sure all moving parts have come to a complete stop.
The Rectangular Shredder Knives Kit is a replacement kit to replace existing dull or damaged knives. The serrated shredder
knives are designed to offer long life and can be reversed if they become dull. To remove the knives or to install a complete
new shredder kit proceed as follows.
NOTE
This shredder kit uses an improved knife pattern to provide
more complete shredding, durability, and easier feeding.
Care must be taken to insure the knives and spacers are
installed properly to maintain rotor balance.
1. Remove belt guards from under engine frame, remove
discharge cover and screen.
2. Remove #10-24 nuts and bolts from knife shafts.
3. Align shaft with 5/8" hole in rear of frame and small hole
in front of machine by the chipper chute.
4. Using a small punch or rod drive the shaft towards and
out the rear 5/8" hole.
5. To assemble, insert shaft through 5/8" hole in rear of
frame and slide knives and spacers in their proper order
(see drawing) onto the shaft. Install a new #10-24 nut
and bolt.
6. Repeat steps 3-5 to assemble the other three shafts.
7. When completed install discharge screen, and discharge
cover, torque all 3/8" bolts to 33 ft-lbs. and test run
machine.
99922205592
Shredder Knives Kit 99944300014
WARNING
The serrated edge of the shredder knives should face the
same direction as the cutting edge of the chipper blades.
Never reuse the #10-24 nut and bolt, always install new
parts when repairing. Never reuse shafts or spacers if they
show signs of wear or abuse. Install new ones.
4
5
9
6
- 1 -
INSTRUCTION SHEET
IMPORTANT
8
7
11
12
4
©2020 ECHO Incorporated. All Rights Reserved.
©2020 ECHO Incorporated. Tous Les Droits Sont Réservés.
©2020 ECHO Incorporated. Todos Los Derechos Reservados.

Publicidad

loading

Resumen de contenidos para Echo 99944300014

  • Página 1 7. When completed install discharge screen, and discharge cover, torque all 3/8" bolts to 33 ft-lbs. and test run machine. ©2020 ECHO Incorporated. All Rights Reserved. 99922205592 - 1 - ©2020 ECHO Incorporated. Tous Les Droits Sont Réservés. ©2020 ECHO Incorporated. Todos Los Derechos Reservados.
  • Página 2: Instruction Sheet

    INSTRUCTION SHEET Shredder Knives Kit 99944300014 SHREDDER KNIVES KIT, PN 99944300014 ITEM PART NO. DESCRIPTION YH450000210 NUT, 10/24 NYLOCK TYPE NM ZP YH415000130 SCREW, SKT HD CAP #10-24 × 1-3/8" PL YH466000020 SHAFT, C/S KNIFE YH475000110 SPACER, 0.75 × 2.170 YH475000120 SPACER, 0.75 ×...
  • Página 3 7. Cuando termine, instale la rejilla de descarga y descarguetapa, apriete todos los pernos de 3/8 “a 33 libras-pie.máquina. ©2020 ECHO Incorporated. All Rights Reserved. 99922205592 - 3 - ©2020 ECHO Incorporated. Tous Les Droits Sont Réservés. ©2020 ECHO Incorporated. Todos Los Derechos Reservados.
  • Página 4: Descripción

    HOJA DE INSTRUCCIONES KIT DE CUCHILLAS TRITURADORAS 99944300014 Eje 1 Eje 2 Eje 1 Eje 3 Eje 2 (Inverso del Eje 1) Eje 4 (Inverso del Eje 2) Eje 4 Rotor Astilladora Eje 3 KIT DE CUCHILLAS TRITURADORAS, PN 99944300 ARTICULO NÚMERO DE PIEZA...
  • Página 5 FEUILLE D’INSTRUCTION KIT DE LAME DE BROYEUSE RECTANGULAIRE 99944300014 Objet : Kit de lame de broyeuse rectangulaire 99944300014 Dispositif: Toutes les déchiqueteuses/broyeuses de 3 po. (excepté SC-2013) Modèle(s) : AVERTISSEMENT Avant d’inspecter ou de réparer une pièce de cette machine, coupez la source d’alimentation, déconnectez le câble de la bougie d’allumage, débranchez la batterie (le cas échéant), et assurez-vous que toutes les pièces en mouvement se sont...
  • Página 6 FEUILLE D’INSTRUCTION KIT DE LAME DE BROYEUSE RECTANGULAIRE 99944300014 KIT DE LAME DE BROYEUSE RECTANGULAIRE, NO DE PIÈCE 99944300014 NUMÉRO DE PIÈCE DESCRIPTION QTÉ PIÈCE YH450000210 ÉCROU 10/24 NYLOCK TYPE NM ZP YH415000130 VIS À TÊTE SKT SCW Nº10-24 × 1-3/8 PO. PL...