Beko ADV5810 Manual Del Usuario página 31

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 19
In order to replace the dichroic lamps, carefully remove
the lamp from the lamp holder with the help of a small
flat screwdriver or a similar tool.
PLEASE NOTE! In doing this operation, please take
care not to scratch the hood.
Replace the bulbs with new ones of the same type.
• Replacing halogen light bulbs (Fig.20):
To replace the halogen light bulbs B, remove the glass
pane
C using a lever action on the relevant cracks.
Replace the bulbs with new ones of the same type.
Caution: do not touch the light bulb with bare hands.
• Replacing LED lamps (Fig.21):
If the appliance version is with LED lamps, the interven-
tion of a specialised technician is necessary to replace
them.
• Commands (Fig.22):
Push-button A = On/off lights switch.
Push-button B = On/off cooker hood switch. The appli-
ance switches on at speed level 1, If the cooker hood is
on depress the push-button for 2 sec. to switch off the
cooker hood. If the cooker hood is at speed level 1 it will
not be necessary to depress the push-button to switch
the cooker hood off. Decreases the motor speed.
Display C = Indicates the motor speed level selected and
activates the timer.
Push-button D = Switches on the cooker hood. In-
creases the motor speed. Touching the key at 3rd speed,
the intensive function runs for 10', then the appliance go
back to work at the original speed. During this function
the display blinks.
Key E = The Timer times the functions on activation for
15 minutes, after which they are switched off. The Timer
is deactivated by re-pressing Key E.
When the Timer is activated the decimal point must
flash on the display. The Timer cannot be activated if the
intensive speed is functioning.
The "clean air" function is activated by pressing key E
for 2 seconds when the appliance is switched off. This
switches the motor on for 10 minutes every hour at the
first speed. During functioning a rotary movement of the
peripheral segments must be visualised on the display.
When this time has passed the motor switches off and
the fixed letter "C" must be visualised on the display
until the motor re-starts after 50 minutes for another
10 minutes and so on. Press any key apart from the light
keys to return to normal functioning. Press key E to
deactivate the function.
• Anti-grease/active charcoal filters saturation:
- When display item C flashes, at a speed where it alter-
nates with the letter F (e.g. 1 and F), the anti-grease
filters must be washed.
- When display item C flashes, at a speed where it alter-
nates with the letter A (e.g. 1 and A), the active carbon
filters must be replaced or washed depending on the type
of filter.
After the clean filter has been positioned correctly, the
electronic memory must be reset by pressing button A
for approximately 5 seconds, until the indication F or A
shown on the display C stops flashing.
• Commands mechanical (Fig.23.A.B) the key symbols
are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
G = MOTOR WORKING indicator.
• Commands luminous (Fig.24.A.B) the key symbols
are explained below:
A = LIGHT
B = OFF
C = SPEED I
D = SPEED II
E = SPEED III
F = AUTOMATIC STOP TIMER - 15 minutes (*)
If your appliance has the INTENSIVE speed function,
from speed THREE, press key E for 2 seconds and it will
be activated for 10 minutes after which it will return to
the previously set speed. When the function is active
the LED flashes.
To interrupt it before the 10 minutes have elapsed, press
key E again.
Some models allow activating this function even with
speed one and two.
By pressing key F for two seconds (with the hood
switched off) the "clean air" function is activated. This
function switches the appliance on for ten minutes
every hour at the first speed. As soon as this function is
activated the motor starts up at the first speed for ten
minutes. During this time key F and key C must flash at
the same time. After ten minutes the motor switches off
and the LED of key F remains switched on with a fixed
light until the motor starts up again at the first speed
after fifty minutes and keys F and C start to flash again for
ten minutes and so on. By pressing any key for the exclu-
sion of the hood light the hood will return immediately to
its normal functioning (e.g. if key D is pressed the "clean
air" function is deactivated and the motor moves to the
2nd speed straight away. By pressing key B the function
is deactivated).
(*) The "AUTOMATIC STOP TIMER" delays stopping of
the hood, which will continue functioning for 15 minutes
at the operating speed set at the time this function is
activated.
• Anti-grease/active charcoal filters saturation:
- When the A key flashes with a 2 second frequency the
anti-grease filters must be washed.
- When the A key flashes with a 0.5 second frequency
the active carbon filters must be replaced or washed
depending on the type of filter.
Once the clean filter has been put back one must reset
the electronic memory by pressing the A key for approxi-
mately 5 seconds until it stops flashing.
• Mechanical controls (Fig.25) the symbols are as
follows:
A = LIGHT/ON-OFF key
B = OFF/FIRST SPEED key
C = SECOND SPEED key
D = THIRD SPEED key.
If the hood is shut off at first, second or third speed, when
- 29 -

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Cib 9600 xCib 9601 xhHci 91731 xh

Tabla de contenido