Ryobi CAG-180M Manual De Utilización página 13

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 25
GB
F
D
E
GENERAL SAFETY RULES
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from intended could result
in a hazardous situation.
BATTERY TOOL USE AND CARE
Ensure the switch is in the off position before
inserting battery pack. Inserting the battery pack
into power tools that have the switch on invites
accidents.
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
Keep battery contact away from all metal objects.
Shorting the battery terminals may cause burning, or
fire.
Keep the power tool clean and dry. Clean with
solvent free cleaning products only. Do not use
petroleum based products such as petrol, or white
spirit.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool
is maintained.
CORDLESS ANGLE GRINDER
SPECIFIC SAFETY RULES FOR GRINDERS
Check that speed marked on the wheel is equal to or
greater than the rated speed of the grinder.
Ensure that the wheel dimensions are compatible with
the grinder.
Grinding wheels shall be stored and handled with care
in accordance with manufacturer's instructions.
Ensure that mounted wheels and points are fitted in
accordance with the manufacturer's instructions.
I
P
NL
S
DK
English
N
FIN
GR
H
CZ
Ensure that blotters are used when they are provided
with the bonded grinding product and when they are
required.
Ensure that the grinding product is correctly mounted
and tightened before use and run the tool at no-
load for 30 s in a safe position, stop immediately if
there is considerable vibration or if other defects are
detected. If this condition occurs, check the machine
to determine the cause.
If a guard is supplied with the tool never use the tool
without such a guard.
Do not use separate reducing bushings or adapters to
adapt large hole grinding wheels.
For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
Check that the work piece is properly supported.
Ensure that sparks resulting from use do not create
a hazard e.g. do not hit persons, or ignite flammable
substances.
Ensure that ventilation openings are kept clear when
working in dusty conditions. If it should become
necessary to clear dust, first disconnect the tool from
the mains supply (use non metallic objects ) and avoid
damaging internal parts.
Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn.
The wheel continues to rotate after the tool is switched
off.
Always wear safety glasses with side shields.
Everyday glasses have only impact resistant
lenses. They are NOT safety glasses. Following
this rule will reduce the risk of eye injury.
Protect your lungs. Wear a face or dust mask
if the operation is dusty. Following this rule will
reduce the risk of serious personal injury.
Protect your hearing. Wear hearing protection
during extended periods of operation.
Following this rule will reduce the risk of serious
personal injury.
Inspect the grinding wheel before use, do not
use chipped, cracked or otherwise defective
products.
Do not use cutting off wheel for side grinding.
Protect your hands. Wear gloves during
operation. Following this rule will reduce the risk
of personal injury.
9
RUS
RO
PL
SLO
HR
TR

Publicidad

Tabla de contenido
loading

Tabla de contenido