Teka DS ISLA Manual De Instrucciones página 18

Manual DS ISLA TEKA.qxd
Accessories supplied
1 150/125 mm reduction.
1 Anti-recoil valve.
4 Screws (M4 x 10).
6 Lock screws (Ø8 x 45).
4 Screws (M4 x 12).
Installation
Fig. 1 (Page 19)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
14 are complied with.
To obtain optimum performance, the external
duct must not be more than FOUR METRES
LONG, have no more than two 90° angles and
its diameter must be at least Ø120.
1) Using the support (O) trace and drill the
where the screw-fittings will sit onto the roof (S)
(Ø8 x 45).
2) Screw the support (O) into the roof with the
screw-fittings (S) (Ø8 x 45).
3) Mount the upper chassis
support (O) using the screws (Q) (M6 x 16).
4) Connect the upper part of the inner tube (not
supplied) to the exit.
5) Mount the upper cover (A8) and attach it to
the upper chassis (A6) with the screws (G) (M4
x 12).
6) Fit the part (A) if the inner tube (not supplied)
is Ø150 or (A) + (B) if it is Ø120.
7) Mount the whole lower unit to the upper
section, attaching it to the roof using the
screws (A10) (M4 x 12) at the required height.
8) Attach the inner tube with a clamp (not
supplied) to (A) or (B) as the case may be.
9) Mount the lower part (A9a) of the cover to
the lower chassis (A7) with the screws (I) (M4
x 12).
10) Adjust the lower part (A9b) of the cover
(A9a) as shown in the diagrams.
Active charcoal filters (Optional)
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active carbon filters.
The active carbon filters have an active life of
18
14/04/2003 12:29 PÆgina 18
between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They must
be replaced once their useful life comes to an
end.
Fig. 1 (Page 19)
1) Mount the diffuser support (A13) onto the
upper chassis (A6) with the screws (A4) (M4 x
12).
2) Adjust the diffuser (A5) over the support
(A13).
3) Connect the upper part of the inner tube (not
supplied) to the circular support exit (A13).
4) Using the support (O) trace and drill the
where the screw-fittings will sit onto the roof (S)
(Ø8 x 45).
5) Screw the support (O) into the roof with the
screw-fittings (S) (Ø8 x 45).
6) Mount the upper chassis
support (O) using the screws (Q) (M6 x 16).
7) Mount the upper cover (A8) and attach it to
the upper chassis (A6) with the screws (G) (M4
x 12).
8) Fit the part (A) if the inner tube (not supplied)
(A6) onto the
is Ø150 or (A) + (B) if it is Ø120.
9) Mount the whole lower unit to the upper
section, attaching it to the roof using the
screws (A10) (M4 x 12) at the required height.
10) Attach the inner tube with a clamp (not
supplied) to (A) or (B) as the case may be.
11) Mount the lower part (A9a) of the cover to
the lower chassis (A7) with the screws (I)
(M4x12).
12) Adjust the lower part (A9b) of the cover
(A9a) as shown in the diagrams.
SET type 1 - Fig. 2 (Page 19)
13)
section of the motor making the holes in the
filters match up (A11) with the pivots (A12) of
the motor carcass.
SET type 2 - Fig. 3 (Page 19)
13) Fit the nut-supports (A14) onto the body of
the kitchen hood.
14) Attach the supports (A15) with the screws
(A16) (M4 x 12) onto the nuts (A14).
15) Mount the carbon filters (A17) introducing
the anchorages into the grooves of the
supports (A15).
Put the filters into the lateral draught
(A6) onto the