Wired Connection - Bowers & Wilkins T7 Wireless Manual De Instrucciones

Ocultar thumbs Ver también para T7 Wireless:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 20
• Once a connection has been established, ensure
that T7 Wireless is selected as the speaker
output. Audio will now be heard through
T7 Wireless.
The paired device memory can be cleared by
press and hold Volume – and Bluetooth button for
2 seconds. The Bluetooth indicator will flash and
T7 Wireless will restart once the memory has been
cleared.
To disconnect a Bluetooth source device from
T7 Wireless press the T7 Wireless Bluetooth button
twice in quick succession. This will disconnect
all Bluetooth connected devices. T7 Wireless
will provide audible feedback when Bluetooth is
disconnected.

5.2 Wired connection

Connect to the Auxiliary input using an appropriate
cable. T7 Wireless will select its Auxiliary input
automatically when a plug is inserted. If the
analogue audio source has an output volume
control, set it initially to around half volume. Use the
T7 Wireless buttons to control volume rather than
the source device volume controls. Only increase
the source volume if T7 Wireless maximum volume
is inadequate.
Note: T7 Wireless will always switch
automatically to its Bluetooth input if an audio
stream is received from a connected Bluetooth
source device.
6. Operating T7 Wireless
Once paired with a Bluetooth source or connected
to a wired analogue audio source, operation of
T7 Wireless is simple.
To increase or decrease volume press the Volume +
or Volume – buttons respectively.
To play or pause Bluetooth streamed audio use the
T7 Wireless Play/Pause button. To skip to the next
track press the Play/Pause button twice in quick
succession. To skip to the previous track press the
Play/Pause button three times in quick succession.
Note: The play/pause button will not control
audio from T7 Wireless Auxiliary input.
To connect to the primary Bluetooth source press
the Bluetooth button.
To disconnect from the currently connected
Bluetooth source press the Bluetooth button twice
in quick succession. If two Bluetooth devices are
connected to T7 Wireless, both devices will be
disconnected. T7 Wireless will provide audible
feedback of Bluetooth disconnection and switch to
the auxiliary input.
To select T7 Wireless analogue wired input insert a
connection plug or disconnect from the connected
Bluetooth source.
To check T7 Wireless battery charge press the
Power button.
To switch T7 Wireless off press and hold the Power
button.
7. T7 Wireless Indicators and Audio cues
Blue flashing
T7 Wireless is in discoverable
mode
Blue solid
T7 Wireless is successfully paired
with a Bluetooth device
Blue blinking
Pairing has failed
(fast flashing)
The LEDs on the side of the product give an
indication of battery life as described in Diagram 4.
Audio cues are heard for the following actions –
Power on
Power off
Bluetooth discoverable mode entered
Bluetooth device connected
Bluetooth devices disconnected
Battery charging initiated
Battery charge low
Battery charge critical
Note: It is possible to toggle the audio cues on
and off by press and releasing 'Play/Pause' and
'+'.
8. T7 Wireless Firmware Update
Updated T7 Wireless firmware may from time to time
be made available for download from the T7 Wireless
support section of the Bowers & Wilkins website.
9. Reboot
To perform a reboot use a straightened paper-clip to
press and hold the Reboot button for two seconds.
T7 Wireless will turn off, press Power on and reboot
will be complete.
Note: Performing a reboot will not clear the
paired device memory.
10. Cleaning T7 Wireless
Wipe surfaces with a dry clean lint-free cloth.
11. Troubleshooting
If you need help troubleshooting a specific problem,
or have a question you'd like answered, please
consult the T7 Wireless support section of the
Bowers & Wilkins website:
www.bowers-wilkins.com
6

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Fp38016

Tabla de contenido