Fitting Instructions - cam CORTINA X3 TRIS EVOLUTION Manual De Instrucciones

INSTRUCTIONS FOR USE
20. Carrycot is suitable for children who cannot seat down unaided, roll or who cannot
lift up on their hands or knees. 21. Car seat and pushchair do not replace a carrycot
or a bed. Should your child need to sleep, then he should be placed in a suitable cot
or bed. 22. WARNING! Do not put a mattress in the carrycot (optional) with a thickness
of more than 20 mm. 23. Frame of the product is suitable for carrycot and car seat
(optional) approved by manufacturer only and provided with qUICKY SYSTEM
mechanism. 24. WARNING! Do not use the frame without carrycot/pushchair/car seat
to carry your child.
CONFORMS TO SAFETY STANDARD - EN 1888:2012

FITTING INSTRUCTIONS

1. Lift the front axle until you hear a "click". ATTENTION! Make
sure that the front axle is correctly locked before proceeding
with assembling.
2. Turn the handle pushing at the same time the 2 buttons B
placed on each side of the handle.
3. To open the pushchair, lift the secondary lock A and operate
the levers C placed on the sides of the handle and lift the product
till it is completely open. ATTENTION: before proceeding with
fitting the other components, make sure that the pushchair is
completely open and make sure that all locking mechanisms are
correctly engaged before using the pushchair.
FITTING THE REAR WHEELS
4. First of all make sure that each single wheel is correctly
matched with the relevant housings and pins, thanks to the
small round stickers (red and blue).
5. Insert the pin on the wheel, pushing the H button and then,
keeping this button pushed down, insert the wheel on the rear
axle, until you hear a "click". Act in the same way on both sides.
ASSEMBLING THE FRONT WHEEL (PIVOTING WHEEL)
6. Gently turn the pushchair upside down so that the handle
touches the floor.
7. Insert the front fork I in its aluminium housing L until you hear
a "click".
8. Lock the front fork I with button M.
9. Slightly unscrew (not completely) bolt N on the edge of axle O.
10. Insert axle O in the front fork I.
11. Place the extra locking device P into the relevant housings q
on both the 2 sides.
12. Screw bolt N (keeping it slightly loosen) so to fit completely
the wheel.
13.PushleverRandmakesureitiswellfitted.ATTENTION: before
proceeding with fitting the rear wheel, make sure that all wheels
have been correctly fitted, so to avoid any danger for your child.
INSTRUCTIONS FOR USE
14. To adjust the handle, push at the same time the 2 buttons
B placed on both the 2 sides and turn to the desired position.
15. To unlock the front fork "I" push upwards button M. To lock
it turn the front fork "I" till part W and button M are aligned. Then
push down button M.
16. To engage the brake, operate pedal J
downwards. To disengage it, lift the pedal J.
17. To adjust the rear suspension K, operate ring A1. If you turn
it clockwise, the rear K suspension gets more rigid. If you turn it
anticlockwise it gets softer.
18. The backrest can be adjusted in 4 positions. To lift it pull
handle A3 of the backrest and adjust the backrest to reach the
desired position. Backrest can be adjusted even without keeping
handle A3 pulled. To lower the backrest it is necessary to keep
handle A3 pulled till you reach the desired position.
19. POSSIBLE COMBINATIONS:
The diagram shows the age/weight for the use of the various
27
features and their correct assembly.
The carrycot and car seat are provided with the special quick
fastening and removal system called "quicky System".
The pushchair is reversible: it can be fitted on the chassis both
rear facing so the seat is facing Mum or Dad or forward facing
so the seat looks towards the road (via vai System Reverse).
REMOVING THE REVERSIBLE SEAT UNIT
We recommend to remove the seat unit while using the
pushchair with the carrycot or the car seat fitted, so to decrease
the weight of this product and to avoid spoiling the cover. The
seat unit is already rear facing fitted on the pushchair frame
when you open the carton.
20. Remove the cover from the armrests.
21. Grip the 2 handles F on both sides of the seat unit.
22. Pull levers v on both handles.
23. Lift the seat unit at the same time. Keep the seat unit stored
for future use. ATTENTION! Never remove the seat unit when
your child is sitting inside the pushchair (fig. 23/a).
FITTING THE CARRYCOT ONTO THE PUSHCHAIR
24. The carrycot is fi tted with a quick lock/release system. Place
the carrycot on the pushchair armrests near the carrycot locking
system "D" (on both sides) and on housings "E". Push the
carrycot down until you hear a "click". Make sure the carrycot is
correctly locked.
25. Operate button "A" and then "B" on the pushchair's armrests
and then lift the carrycot.
USING THE CARRYCOT
26. Rocking mode;
27. adjustable handle with safety mechanism,
28. ventilated bottom,
29. raising the carrycot's backrest (29a) and lowering the
carrycot's backrest (29b),
30. fitting the carrycot's hood,
31. unlocking the carrycot's hood.
FITTING AND RELEASING THE CAR SEAT ONTO THE
PUSHCHAIR
32. The car seat is fitted with a quick lock/release system. Place
the car seat on the pushchair armrests near the locking system
and on housings "E" on both armrests. Push the car seat down
until you hear a "click". Make sure the car seat is correctly locked.
33. Use the bumper bar at all times when the car seat is fitted
onto the pushchair.
34. Operate button "A" and then "B" on the pushchair's armrests
and then lift the car seat.
FITTING AND ADJUSTMENT OF THE 5-POINT HARNESS:
35. WARNING! Before fitting the belts, look carefully at the
diagram to check that the seat fastening systems correspond
correctly with: the shoulder belts ("s" with "S1" or "S2"), the waist
belt ("a" with "A") and the crotch strap ("g" with "G1" or "G2").
WARNING! Choose the correct slots according to the age and
size of the baby: "G1" and "S1" from 0 to 6 months, "G2" and "S2"
from 6 to 36 months.