Jacuzzi Whirlpool Bath BUILDER Serie Manual De Instalación Y Operación página 17

WIRING DIAGRAM RAPIDHEAT
120V SINGLE PHASE POWER SUPPLY
PROTECTED BY A GROUND FAULT CIRCUIT
INTERRUPTOR
NEUTRAL N L1 LIVE
FUSED DISCONNECT SWITCH
OR CIRCUIT BREAKER
FIELD WIRING
JUNCTION BOX
DO NOT OPERATE THE WHIRLPOOL BATH UNLESS
THE HEATER IS CONNECTED TO A CLASS A GFCI
(GROUND FAULT CIRCUIT INTERRUPTOR). TEST
THE GFCI AT LEAST ONCE A MONTH.
WIRING DIAGRAM BATH
120V SINGLE PHASE POWER SUPPLY
PROTECTED BY A GROUND FAULT CIRCUIT
INTERRUPTOR
NEUTRAL N L1 LIVE
FUSED DISCONNECT SWITCH
OR CIRCUIT BREAKER
N L1
MOTOR
DO NOT OPERATE THE WHIRLPOOL BATH UNLESS
IT IS CONNECTED TO A CLASS A GFCI (GROUND
FAULT CIRCUIT INTERRUPTOR). TEST THE GFCI AT
LEAST ONCE A MONTH.
(CANADA ONLY)
OPTIONAL:
30 MINUTE TIMER
(SINGLE POLE SWITCH)
WALL MOUNTED
ON/OFF SWITCH
HEATER
(CANADA ONLY)
OPTIONAL:
30 MINUTE TIMER
(SINGLE POLE SWITCH)
WALL MOUNTED
ON/OFF SWITCH
FIELD WIRING
JUNCTION BOX
Drain Information
A drain/overflow assembly (sold separately) must be installed on
the bath, water tested, and connected to the sanitary system of the
house. After opening the carton, inspect for damage and verify that
the kit is of the proper finish. In the Jacuzzi Whirlpool Bath drain/
overflow kit, note that the waste flange, strainer, overflow cover and
cover screws are packaged in a separate package within the kit to
protect the trim finish. Follow the installation instructions provided
with the drain/overflow kit. After the drain is fully installed, test for
proper drainage. If the unit does not drain properly, rectify this condi-
tion before proceeding with the installation. Jacuzzi Whirlpool Bath is
not responsible for removal and or reinstallation costs.
NOTE: Watertight installation of the drain is the installer's
responsibility. Drain leakage is excluded from the Jacuzzi Whirl-
pool Bath warranty of this product.
Plumbing
Pump, jets, and suction fittings for the whirlpool system are fac-
tory plumbed in schedule 40 PVC piping.
All Jacuzzi Whirlpool Bath products are factory tested for proper
operation and watertight connections prior to shipping. If leaks are
detected, notify your Jacuzzi Whirlpool Bath Dealer. Do not install
the unit.
Water Supply
Consult local authorities for plumbing code requirements in your
area.
IMPORTANT: Proper installation of the fill spout plumbing and
compliance with local codes are the responsibility of the installer.
Jacuzzi Whirlpool Bath does not warrant connections of water
supply fittings and piping, fill systems, or drain/overflow sys-
tems. Nor is it responsible for damage to the bath which occurs
during installation.
CAUTION: A nonflammable protective barrier must be placed
between soldering work and bath unit to prevent damage to the
bath.
Clean-Up After Installation
To avoid dulling and scratching the surface of the bath, never use
abrasive cleaners. A mild liquid detergent and warm water will clean
soiled surfaces.
Remove spilled plaster with a wood or plastic edge. Metal tools
will scratch the surface. Spots left by plaster or grout can be removed
if lightly rubbed with detergent on a damp cloth or sponge.
Paint, tar, or other difficult stains can be removed with paint thin-
ner, turpentine, or isopropyl alcohol (rubbing alcohol).
Minor scratches which do not penetrate the color finish can be
removed by lightly sanding with 600-grit wet/dry sandpaper. You can
restore the glossy finish to the acrylic surface of the bath with a spe-
cial compound, Meguiar's #10 Mirror Glaze. If that is not available,
use automotive rubbing compound followed by an application of au-
tomotive paste wax.
Major scratches and gouges which penetrate the acrylic surface
will require refinishing. Ask your Jacuzzi Whirlpool Bath dealer for
special instructions.
15