Publicidad
Idiomas disponibles
Idiomas disponibles
HEIGHT ADJUSTMENT
3 Preset Programmable Controller
OPERATING THE CONTROLLER
Press and hold either the
up
or
down
•
desired height.
To adjust to a stored height in memory, use the three memory
•
position buttons.
A.
Press and hold the numbered button that has the saved
height stored into memory.
B.
The desk will raise or lower until it reaches the stored
height.
•
As a safety feature, the user must continuously hold down the
button in order for the desk to move. Note the worksurface
slows when approaching the lowest range for additional safety.
STORE HEIGHT INTO MEMORY
To set into memory the desired height for either seated or standing
work, use the three memory position buttons.
Press either the
up
or
down
button to reach the desired height.
•
Press the
s
button once.
•
•
The display will flash
s
for two seconds. During this time
press your choice of memory position buttons 1-3 to set that
particular height.
To save additional heights repeat this sequence using the
•
remaining 2 buttons.
SAVE – KEEP WITH DESK
Cable Management
When installing equipment, either on the worksurface or below,
be sure that the connecting cables are free from obstruction.
A trough is provided to manage excess base controller wires and
can be found on the underside of the worksurface. Use this trough
to minimize possible entanglements.
Workstation Setup and Use
WARNING
RISK OF SERIOUS INJURY OR DEATH.
Raising or lowering desk can trap or crush body parts.
• Maintain > 1 inch (25 mm) gap above objects on desk at max
height, and between desk and adjacent objects.
button to reach the
• Locate desk, accessories and nearby objects to allow
movement of worksurface and modesty panel through full range
without pulling cords, trapping body parts, or colliding with
anything (shelves, electrical plugs and cords, door knobs,
window sills, storage cabinets, etc.).
• Verify power cords for all accessories – computer, lights,
monitors, etc. – are long enough to reach outlets through full
range of height adjustment without strain on cords.
• Always check for proper operating clearance before placing
any item on, above, or below the worksurface.
Maintenance and Cleaning
Regularly clean dust and dirt from lifting columns. To ensure all
surfaces are thoroughly cleaned, make sure the lifting columns are
fully extended to their maximum height. Also, be sure to inspect
cables and lifting columns for damage. Check all connections for
both correct function and secure mounting.
DANGER
To reduce risk of electric shock, always unplug desk from
the electrical power outlet before cleaning.
NOTE: A damp cloth is recommended. To protect the painted
surfaces, use a cleanser that is not highly alkaline or acidic.
A pH neutral product is ideal.
Please do not move the desk without help. Refer to the guidelines
at the end of the assembly directions, or contact your facilities group
for assistance.
Troubleshooting
If you are having trouble with your desk, try the simple steps
outlined below. If problems persist, please refer to the Elective
Elements Height-Adjustable Desk troubleshooting guide.
POWER-SAVING CONTROL BOX:
The control box automatically powers down into 'standby'
•
mode after approximately 10 seconds of inactivity.
During standby mode, the control box only consumes 0.1 watt
•
of power.
With the control box in standby mode, the desk can
•
lose power without affecting the synchronization of the
lifting columns. However, if the control box is still active, and
not in standby mode, a power loss will require that the lifting
columns be re-synchronized.
•
Power fluctuations and brownouts can also cause the need for
re-synchronization.
Note:
The control box does not re-set (initialize) by being unplugged
and plugged back in. Refer to the initialization procedure below.
INITIALIZING THE CONTROL BOX:
•
In the unlikely event that an error occurs, press and hold the
up
and
down
button simultaneously for 5 seconds to reset the
control box.
Synchronize the lifting columns as outlined below.
•
SYNCHRONIZING LIFTING COLUMNS:
•
Verify nothing is in the way, then operate the desk all the way
down to the lowest position, and release the
•
Press the
down
button again, and hold.
•
After a few seconds, the desk will visibly move up and down,
settling to its correct 'bottom' position.
•
The lifting columns are now synchronized via the software
in the control box.
•
Operate the desk all the way up and down to confirm
proper function.
Part Number # 1066814001 Rev. A - 1/14 © 2018
All rights reserved. All specifications subject to change without notice. Printed in U.S.A.
down
button.
®
Visit steelcase.com
Publicidad
