LauraStar SMART I Manual De Instrucciones página 6

Start up
CAUTION: Always fill the water reservoir (11) completely
before turning on your Laurastar. Operating the appliance
without water could damage the appliance.
PLEASE NOTE: Operating the appliance without water will void any
limited warranties provided with your appliance.
A
Installation of the anti-scale cartridge and filling
• Check that the power plug is disconnected from the mains socket.
• Set the ironing board to its highest position.
• Take the water reservoir (11) out. Take off the water reservoir lids.
Install the anti-scale filter (13).
• Fill the reservoir with tap water. The filtered water has to reach the
MAX level.
• Close the water reservoir with the lids and put the reservoir back on the
B
steam generator (15).
• If the water does not flow, soak the anti-scale filter in cold water for 3
minutes.
User interface
• ON/OFF = the green indicator light flashes until the appliance is ready to
be used.
ON/OFF
• = Option Laurastar SenSteam. If your appliance is equipped with the
Laurastar SenSteam option (17), the white indicator light signals that the
function is on.
SenSteam
• = Option Pulsed Steam. If your appliance is equipped with the Pulsed
Steam option (18), the white indicator light signals that the function is ON.
Pulse
Fan speed button (19) = choice of four speeds. The white indicator light
signals the intensity chosen.
Fan speed
• Empty water light (20) = the red drop shaped indicator light signals that
Water
there is no more water in the reservoir (11).
Switching on your appliance
C
• Insert the power plug (23) in the socket. If your model is equipped with the
automatic rewinder, first pull the electric cable untill the end-of-cable mark
is visible at the rewinder opening.
• Press the main ON/OFF button (16), the green indicator light will flash for
3-6 min.
3-6 minutes.
• When the green indicator light stops flashing and stays on, the appliance is
ready. You can start ironing.
• NOTE: For your comfort and safety, your Laurastar system will
switch off after 10 minutes of non-use.
A
B
C
- 9 -
NOTE: Before ironing, or after an extended break, press the iron's
steam button (9) 2 or 3 times, while pointing it away from the clothes.
This will release any condensation from the iron and prevent water
marks on the clothes.
CAUTION : Do not point the iron at people or pets while using
vertical steam.
Ironing
A
Two ironing modes
For the best possible steam ironing result, we offer two modes of ironing :
• Blower mode :
activates the fan (24) in blower mode. this blows air into the fabric from
below, helping to reduce unwanted creases.
• Vacuum mode :
activates the fan (24) in vacuum mode. This draws in air, holding the
B
garment in place on the board to facilitate perfect pleats.
Press the vacuum/blower button (10) to switch from blower to vacuum mode
and vice versa. You can adjust the intensity (4 speeds) pressing the fan speed
button (19) on the user interface of the steam generator.
LAURASTAR SENSTEAM (17) (certain models only)
C
Laurastar SenSteam (17) allows you to obtain an automatic steam diffusion
without pressing the steam button (9). The steam is automatically activated
when the iron moves forward and stops when the iron rests or moves back
.
C
To switch back to regular mode, press the Laurastar SenSteam button (17)
again.
PULSE (18) (certain models only)
Press the pulsed steam button (18) to activate the pulse function. Then press
D
the steam button (9) to automatically generate small and regular steam jets
. To switch back to regular mode, press the pulsed steam button again (18).
D
Steam principle
Perfect ironing requires diffusion of steam across the fabric, in order to relax
the fibres, and drying to fix them in place. Creases can only be completely
removed if these conditions are present.
Advice: For best results, first iron the item with steam and then iron it again
without steam, thereby enabling the iron to dry the fabric.
Protective soleplate (27)
The protective soleplate is indispensable for dark-coloured fabrics which can
Pressing the vacuum/blower button (10) on the iron
A
Pressing the vacuum/blower button (10) again,
B
- 10 -
EN