DeWalt DW892 Manual De Instrucciones página 2

WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face and body.
• The label on your tool may include the following symbols. The symbols and their definitions
are as follows:
V .....................volts
Hz ...................hertz
min .................minutes
or DC .....direct current
...................Class I Construction
.......................(grounded)
...................Class II Construction
(double insulated)
.../min ............per minute
IPM .................impacts per minute
SPM ...............strokes per minute
SAVE THESE INSTRUCTIONS FOR FUTURE USE
Motor
Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than
10% will cause loss of power and overheating. D
not operate, check power supply.
COMPONENTS (Fig. 1, 2)
WARNING: Never modify the power tool or any part of it. Damage or personal injury could
result.
A. Fixed blade
B. Moving blade
C. Curl deflector
INTENDED USE
The DW892 14-gauge shear is designed for professional cutting at various work sites (i.e.,
construction sites). DO NOT use under wet conditions or in presence of flammable liquids or
gases.
These 14-gauge shears are professional power tools. DO NOT let children come into contact
with the tool. Supervision is required when inexperienced operators use this tool.
ADJUSTMENTS
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Setting the Blades (Fig. 2, 3)
VERTICAL CLEARANCE
Position the moving blade at the top of its stroke. Adjust the vertical clearance so that the "V"
shaped opening appears as in Figure 2.
HORIZONTAL CLEARANCE
The upper movable blade (B) must be centered to correspond with the position of the lower
fixed blade (A) as shown in Figure 2 by releasing the clamp screw with the key provided.
The lower blade must be positioned relative to the upper blade ac cording to the thickness of the
material to be cut. The shear is sup plied with a gauge to facilitate this adjustment.
1. Loos en the clamp screw (I) and withdraw the lower blade away from the upper blade.
2. Loosening set screw (H).
3. Insert the appropriate size feeler gauge (J) between the two blades and slowly tighten
screw (H) until both blades are in contact with the gauge.
4. Lock the lower blade by tight ening screw (I) and tighten the hex nut (G) to lock set screw (H).
OPERATION (FIG. 1, 4, 5)
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Switches (Fig. 1)
To start tool, depress the paddle switch (D). To turn the tool off, release the paddle. The paddle
switch can be locked on by engaging the lock button (E) located near the rear of the tool, while
holding the paddle depressed. Always be sure that the tool is not locked on before plugging in. To
turn the tool off when it is locked on, squeeze and release the paddle once.
Hold the shear positioned so the main body is parallel to the work (K) and the cutters are at right
angle to the work (Fig. 4). Engage the cutters with the edge of the material to be cut, and apply
only sufficient forward pressure to start cutting. The relative position of the cutters to the work
is critical, and it may be necessary to tilt the tool forward or backward until the best cutting rate
is achieved. Too much tilt will stop the cut. Blades must be sharpened in accordance with the
angles in Figure 5, using the template (L) provided.
MAINTENANCE
WARNING: To reduce the risk of injury, turn unit off and disconnect it from power
source before installing and removing accessories, before adjusting or when making
repairs. An accidental start-up can cause injury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry air at least once a week.
To minimize the risk of eye injury, always wear ANSI Z87.1 approved eye protection when
performing this.
WARNING: Never use solvents or other harsh chemicals for cleaning the non-metallic parts
of the tool. These chemicals may weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid.
Lubrication
D WALT tools are properly lubricated at the factory and are ready to use. Tools should be
E
relubricated regularly every 60 days to 6 months, depending on usage. Tools used constantly on
production or heavy-duty jobs and tools exposed to heat may require more frequent lubrication.
This lubrication should only be attempted by trained power tool repairmen such as those at
D WALT certified service centers.
E
Accessories
WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the risk
of injury, only D WALT recommended accessories should be used with this product.
E
Recommended accessories for use with your tool are available at extra cost from your local dealer
or authorized service center. If you need assistance in locating any accessory, please contact
D WALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call 1-800-4-D
E
(1-800-433-9258) or visit our website: www.dewalt.com.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including
brush inspection and replacement) should be performed by a D
a D WALT authorized service center or other qualified service personnel. Always use identical
E
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRANTY SERVICE: Registering your product will help you obtain more efficient
warranty service in case there is a problem with your product.
• CONFIRMATION OF OWNERSHIP: In case of an insurance loss, such as fire, flood or
theft, your registration of ownership will serve as your proof of purchase.
A .........................amperes
W ........................watts
or AC .............alternating current
or AC/DC......alternating or direct current
n o .......................no load speed
n .........................rated speed
.......................earthing terminal
........................safety alert symbol
BPM ...................beats per minute
RPM ...................revolutions per minute
sfpm ...................surface feet per minute
WALT tools are factory tested; if this tool does
E
D. Paddle switch
E. Lock button
WALT, have not been tested
E
WALT factory service center,
E
FIG. 1
A
FIG. 2
A
2/3 1/3
FIG. 4
K
90º
BLADE / LAME / HOJA
Thickness .1 mm (.004")
Épaisseur de 0,1 mm (0,004 po)
Grosor 0,1 mm (0,004")
Thickness .2 mm (.008")
Épaisseur de 0,2 mm (0,008 po)
Espesor 0,2 mm (0,008")
Thickness .3 mm (.012")
Épaisseur de 0,3 mm (0,012 po)
Grosor 0,3 mm (0,012")
• FOR YOUR SAFETY: Registering your product will allow us to contact you in the unlikely
event a safety notification is required under the Federal Consumer Safety Act.
Register online at www.dewalt.com/register.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for
E
three years from the date of purchase. This warranty does not cover part failure due to normal
wear or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, D
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
E
during the first year after purchase.
If you are not completely satisfied with the performance of your D
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products
sold in Latin America, see country specific warranty information contained in the packaging, call
the local company or see website for warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-4-D WALT (1-800-433-9258) for a free replacement.
E
Défi nitions : lignes directrices en
WALT
E
Les définitions ci-dessous décrivent le niveau de danger pour chaque
mot-indicateur employé. Lire le mode d'emploi et porter une attention
particulière à ces symboles.
DANGER : indique une situation dangereuse imminente qui, si elle n'est pas
évitée, entraînera la mort ou des blessures graves.
AVERTISSEMENT : indique une situation potentiellement dangereuse qui,
si elle n'est pas évitée, pourrait entraîner la mort ou des blessures graves.
ATTENTION : indique une situation potentiellement dangereuse qui, si elle
n'est pas évitée, pourrait entraîner des blessures légères ou modérées.
AVIS : indique une pratique ne posant aucun risque de dommages corporels
mais qui par contre, si rien n'est fait pour l'éviter, pourrait poser des risques de
dommages matériels.
D
C
E
B
FIG. 3
B
FIG. 5
12º
MATERIAL THICKNESS / ÉPAISSEUR DU MATÉRIAU /
GROSOR DEL MATERIAL
For 1 mm plate thickness (.036"–20 Gauge)
Pour plaque d'une épaisseur de 1 mm (0,036 po–calibre 20)
Para un grosor de placa de 1 mm (0,036"–Calibre 20)
For 1.5 mm plate thickness (.060"–16 Gauge)
Pour plaque d'une épaisseur de 1,5 mm (0,060 po–calibre 16)
Para un grosor de placa de 1,5 mm (0,060"–Calibre 16)
For 2 mm plate thickness (.075"–14 Gauge)
Pour plaque d'une épaisseur de 2 mm (0,075 po–calibre 14)
Para un grosor de placa de 2 mm (0,075"–Calibre 14)
WALT (1-800-433-9258). This warranty does not apply to
E
WALT tools are covered by our:
E
1 YEAR FREE SERVICE
90 DAY MONEY BACK GUARANTEE
matière de sécurité
D
J
G
H
I
BLADE GAP
JEU DE LA LAME
ESPACIO DE
LA HOJA
B
B
5º A
13º
L
WALT Power Tool, Laser, or
E