Important Safety Instructions - Bestway 65019 Manual Del Usuario

#65019
Boat
Components:
• Repair Patch
• Deflation Pipe
#65020
Boat
Components:
• Repair Patch
• Deflation Pipe
1
(#65020)
6
NOTE: All drawings for illustration purpose only. May not reflect actual product. Not to scale.
1 2 3
Backrest Seat Inflatable floor Screw valve
EN ISO 6185 - 1 TYPE III
0.0351 bar
= = 1
0.509 psi
= 100 kg (220.0 lbs.)
+
Sheltered Water
TYPE OF MODEL NUMBER: 65019
MANUFACTURER:
COUNTRY OF ORIGIN: CHINA
Oar blade x 2
Shaft x 1
Coupling x 2
Safety rope
Oar
cm 11 12 13 14 15
Inflating Control
• Inflation Control
Oar blade x 4
Shaft x 2
Coupling x 4
Safety rope
Oar
cm 11 12 13 14 15
Inflating Control
• Inflation Control
7
3
5
4 5 6
Safety rope Footrest
EN ISO 6185 - 1 TYPE III
0.0351 bar
= 0 =
0.509 psi
= 160 kg (350.0 lbs.)
+
300m
Sheltered Water
TYPE OF MODEL NUMBER: 65020
MANUFACTURER:
COUNTRY OF ORIGIN: CHINA
WARNING: To avoid damage to the boat and injury to passengers, please don't exceed the data
given on the builder's plate.
Technical Specifications
Item Inflated Size
2.80 m x 75 cm
65019
110" x 30"
3.57 m x 77 cm
65020
141" x 30"
Follow all the Safety and Operating Instructions. If you don't follow this instructions, it may cause
overturn, explode the boat and causes to drowning.
1. Do not exceed the maximum recommended number of persons. Regardless of the number of
persons on board, the total weight of persons and equipment must never exceed the maximum
recommended load. Always use the seats /seating spaces provided.
2. When loading the craft, never exceeds the maximum recommended load: Always load the craft
carefully and distribute loads appropriately to maintain design trim (approximately level). Avoid
placing heavy weights high up.
NOTE: The maximum recommended load includes the weight of all persons onboard, all provisions
and personal effects, any equipment not included in the light craft mass, cargo (if any) and all
consumable liquids(water, fuel, etc.).
3. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected
and used at all times.
4. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars,
and air valves, to ensure everything is in good condition and tightly secured. Please stop to repair if
you find any damage.
5. Buckets, water scoops and air pumps should always be available in case of air leakage or if the
boat takes on water.
6. When the boat is in motion, all passengers must remain seated at all times to avoid going
overboard. Keep the boat balanced. Uneven distribution of persons or load in the boat may cause
overturn the boat and drowning.
7. Use the craft in sheltered water, up to 300m (984 feet). Be careful with natural factors such as wind,
tide waters and tidal waves. BE AWARE OF OFFSHORE WINDS AND CURRENTS. Always wear
a lifejacket!
Rope
8. If one chamber is punctured when the boat is in the water, it may be necessary to fully inflate the
other air chamber to prevent the boat from sinking.
9. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells,
glass, etc. may punctured the boat. To avoid damage do not drag the boat on rough surfaces.
10. The boat is intended for beach use, short-time and short-distance cruising.
11. Be aware of the potential harmful effects of liquids such as battery acid, oil, petrol. The liquids may
damage your boat.
12. Inflate according the numbered air chamber and rated pressure on the boat, or it will cause over
inflation and boat explosion. Exceeding the data given on the capacity plate may cause the craft to
damage, overturn and lead to drowning.
13. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.
14. Know how to operate a boat. Check in your local area for information and/or training as needed.
Inform yourself about local regulations and dangers related to boating and/or other water activities.
4
SAVE THESE INSTRUCTIONS
Inflation
NEVER USE HIGH PRESSURE AIR TO INFLATE INFLATABLES. THIS CAN DAMAGE YOUR
PRODUCT AND VOID YOUR WARRANTY
1. Screw Valve
Screw the screw valve onto the air intake valve on the boat. Open the top cover of the screw valve,
insert the inflation hose and inflate. Once inflation is finished, fasten the top cover of the screw valve.
If over inflation occurs, open the top cover of the screw valve, simply use the provided deflation pipe to
2
deflate slightly. Hold the pipe until the desired pressure is reached and then fasten the top cover of the
screw valve.
2. Safety Valve
Open the safety valves and inflate. Close the safety valves after inflation and press them into the air
chambers.
When inflating your boat, never let anyone sit, step or even lean on the boat.
Deflation
1. Screw Valve
Unscrew the screw valve from the boat.
7
Printed scale
= 1 = 1
2. Safety Valve
Pull out the safety valves from the air chambers. Open the safety valves and pinch the bottom to
deflate.
300m
3
Recommended
Maximum load capacity
working pressure
0.0351 bar
100 kg (220 Ibs.)
0.509 psi
0.0351 bar
160 kg (350 Ibs.)
0.509 psi
Warning

IMPORTANT SAFETY INSTRUCTIONS

Maximum number of persons
1 adult
1 adult + 1 child
S-S-001716