Bestway 65019 Manual Del Usuario página 4

Assembling of the boat
NEVER USE THE AIR PRESSURE MACHINE TO INFLATE
• Spread the boat on a level and even ground.
• Inflate the air chambers with a HAND air pump.
• Pay careful attention to the inflation pressure during inflation. If you use a pressure gauge (not
included in the packaging, we suggest to buy the Bestway Pressure Gauge product code P5C320),
the pressure must be the same as specified in the table in the above Technical Specification section.
If you use the inflation control (see the below illustration) provided with the product, inflate the product
until the printed scale on the boat (see position 7 page 2) is charged up to the same level as that of
the supplied scale. (Refer the table and Illustration bellow)
Caution: Under and over-inflation of the boat will result in safety hazards. It is better to check the
pressure of the boat each time before using.
• Never stand on or rest objects on the boat during inflation.
• Inflate bottom chamber and other accessories such as seat until it is stiff to the touch but NOT hard.
Item Product Inflated Size Deflated Size
2.80 m x 75 cm (110" x 30")
65019 10cm
3.57 m x 77 cm (141" x 30")
65020 10cm
NOTE: All drawings for illustration purpose only. May not reflect actual product.
Safety rope installation
Insert the rope into the hole of the grommets orderly, then tighten the rope.
Caution: 1. Safety ropes shall be fitted to both sides of the bow and stern areas only and shall not
impede the normal operation of the craft.
2. Do check carefully if the safety rope is tightened well.
Backrest (only for #65020) and footrest assembly
After inflating the backrest, tighten the grommets on the bottom of the backrest and the grommets on
the bottom of the boat by rope.
Put the inflated footrest into the front of the boat, make sure the footrest not entangle the feet of the
occupants in the event of a capsize.
Oars Installation
Storage
1. Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions.
2. Use a cloth to gently dry all surfaces.
Note: Do not dry the product in direct sunlight. Also, never dry with equipment such as electric
blowers. Doing so will cause damage and shorten the boat's life span.
3. Deflate the hull chambers. Deflate all the hull chambers at the same time so the air-pressure drops
together. This will prevent damage from occurring to the boat inner structures.
4. Next deflate the floor.
5. Fold the boat from front to back to remove additional air. You can also use a pump to drain any
remaining air.
6. Keep all accessories for future use.
Repair
1. If there is a small puncture, repair it according to the instruction on repair patch.
2. If the hole is too big to be repaired with the provided patch, purchase a Bestway repair kit or send the
boat to a speciality shop to make the repair.
Registration (For US/Canada customers only)
If you need to register your boat, please have the boat Hull Identification Number and model name
ready and then visit www. bestway-service.com to obtain your Certificate of Origin, or you can send
e-mail to info@bestway-northamerica.com for the Certificate of Origin.
PLEASE KEEP THIS MANUAL IN A SECURE PLACE, AND HAND IT OVER TO THE NEW OWNER
WHEN YOU SELL THE CRAFT.
Inflated Size Chamber 2 Inflated Size Chamber 3
11.1cm 10.4cm
11.1cm 10.4cm
#65019
Barco
Components:
• Remendo De Reparaçao
• Tubo de Esvaziamento
#65020
Barco
Components:
• Remendo De Reparaçao
• Tubo de Esvaziamento
1
(#65020)
6
NOTA: Todos os desenhos são somente para fins de ilustração. Podem não reflectir o produto actual.
Não estão à escala.
1 2
Apoio para conforto Assento inflável Piso insuflável Válvula de ar Corda de segurança Pedana
EN ISO 6185 - 1 TIPO III
0.0351 bar
= = 1
0.509 psi
= 100 kg (220.0 lbs.)
+
ÁGUAS ABRIGADAS
NÚMERO DO TIPO DE MODELO: 65019
FABRICANTE:
PAÍS DE ORIGEM: CHINA
4
Lâmina de remo x 2
Haste x 1
União x 2
Remo
cm 11 12 13 14
Escala de controle
para a inflagem
• Controlo de Enchimento
Lâmina de remo x 4
Haste x 2
União x 4
Remo
cm 11 12 13 14
Escala de controle
para a inflagem
• Controlo de Enchimento
7
3
5
3 4 5
EN ISO 6185 - 1
0.0351 bar
= 0 =
0.509 psi
+
300m
ÁGUAS ABRIGADAS
NÚMERO DO TIPO DE MODELO: 65020
PAÍS DE ORIGEM: CHINA
Corda de
segurança
15
Corda de
segurança
15
Corda
4
2
6 7
Escala impressa
TIPO III
= 1 = 1
= 160 kg (350.0 lbs.)
300m
FABRICANTE:
S-S-001716