Machine Use - Rupes S145EL Instrucciones Para La Puesta En Servicio, Uso Y Mantenimiento

MACHINE USE

T
he machine can operates in manual or automatic mode: to
select the mode, turn the switch (12) to the right (automatic
mode) or to the left (manual mode) (pic. 23). The green
indicator (13) turns on when the vacuum motor starts.
Using the machine in automatic mode (A)
Automatic operations means that the vacuum starts when an
electrical or pneumatic tool is turned on.
The vacuum will automatically turn off eight seconds after the
tool is turned off.
Using the machine in manual mode (M)
Manual operations means that the vacuum runs continuously.
Power on the front panel outlet socket is permanently active
during manual running.
Adjusting the vacuum level
The vacuum level can be adjusted in both operating modes by
turning the knob (12) towards the "min" position until the
desired power is reached.
Automatic cleaning of the filters
The machine has a timed filter cleaning system that maintains
the vacuum strength constant.
It is also possible to perform a complete cleaning cycle as
follows (pic. 19):
- switch the machine off;
- cap the vacuum sleeve;
- restart the machine keeping the sleeve capped for 15 seconds.
Suction hose setting
(S145EM -S145EPM)
For operators safety the appliance for M class dust are
provided with an indicator which operates in case of the air
velocity throught the hose falling below 20 m/sec.
Check the hose diameter and set the correct value on the front
panel throttle (32) (pic. 23).
To be used with genuine RUPES hoses.
Acoustic alarm operates
(S145EM - S145EPM)
In case of acoustic alarm on locate the causes (C.) and redress
(R.) it with the action recommended in the following procedure:
C: Power set-up too low;
R: Increase the suction power;
C: The hose diameter doesn't match with the hose set-up on
the front panel;
R: Set the hose diameter knob (32) on the right diameter;
C: Clogged or bended hose;
R: Check and set straight the hose;
C: Dust bag full;
R: See dust bag "REPLACEMENT SECTION";
C: Clogged filers;
R: See filter cartridges "REPLACEMENT SECTION".
After operating in hazardous dust contaminated
environment all appliance parts must be considered as
contaminated; before handling the appliance out the
contaminated area or servicing it, remove all the dust from it
with vacuum or cloth, seal the dust container with the rubber
cap (33), and store hose and accessories in a sealed bag.
Wet vacuum
Before vacuuming liquids, remove the dust bag(paper or
plastic) and replace the paper filters cartridges with polyester
ones. The filters should be damp after vacuuming.
Do not operate with dry dust with wet filters!
12
Liquid level indicator
The vacuum motor stops and the liquid level indicator (14)
turnes on when the the liquid sensor (24) detects the bin (25)
full. To reset empty the bin (25) .
MAINTENANCE
A yearly technical check on parts and filtering system by
an authorized service centre is required.
Service indicator (15)
The indicator turns on for scheduled service to keep the
machine working conditions.
When warning light is on contact an authorized service centre
to check and service the appliance and reset the warning light.
The prolongated use of the vacuum cleaner with the warning
light on can cause more maintenance operation.
Ordinary check operations
For user servicing, the appliance must be dismantled,
cleaned and serviced, as far as it is reasonably
practicable, without causing risk to the maintenance staff
and others. Suitable precautions included contamination
before dismantling, provision for local filtered exhaust
ventilation where the appliance is dismantled (according to
local regulations), cleaning of the maintenance area and
suitable personal protection.
- check the vacuum hose conditions;
- clean the liquid level sensor (24);
- check the power cord, plug and outlet socket conditions: in
case contact an authorized service centre for replacement;
- check the dust bag: do not exceed recommended weight and
capacity! In case of laceration or perforation of the dust bag
check the filter cartridge and eventually ask for replacement to
an authorized service centre;
- check filter cartridges condition (23). In case of lacerations or
perforations contact an authjorized service centre for
replacement.
Do not use the appliance without the full filter set fitted!
Bag replacement
Do not spread dust during dust bag replacement!
- wear an adeguate dust mask;
- detach the head pushing the side hooks (11) and remove the
head (1) (pic. 7-8).
Paper bag (cod. 042.1108/5):
- S 145EM – S 145EPM: seal the dust container with the
appropriate cap (33);
- remove the full bag closing the nozzle with the cap provided
(pic. 12 and 13);
- put the new bag inserting the nozzle as illustrated (pic. 14).
Plastic bag:
- remove the full plastic bag (pic. 9);
- place the new bag, verifying that the nozzle is positioned on
the inlet (pic. 10);
- turn the bag edge as shown (pic. 11); make sure to keep the
compensation holes inside the bin.
Only use genuine RUPES dust bags.
Spare bags should be kept in dry places!
Follow local legal regulations for disposal.