Descargar Imprimir esta página

Publicidad

Enlaces rápidos

BE365 Door Preparation Instructions For Door With Existing Holes
1
Measure Door Width
If the door is thinner than 1³⁄₈"
or thicker than 1³⁄₄", then the
lock will not fit properly on the
door.
2
Measure for Backset
If existing backset is not 2³⁄₈"
or 2³⁄₄", then the lock will not
fit properly on the door.
3
Measure Hole Sizes
If hole sizes are larger than those shown, then the lock will not fit
properly on the door.
If hole sizes are smaller than those shown, see steps 4 and 5.
1"
4
If Needed, Enlarge
Hole in Door
If hole in door is smaller
than 2¹⁄₈", then use 2¹⁄₈"
hole saw to enlarge hole.
Drill Bits Needed:
¹⁄₈", ⁷⁄₈", 1"
1³⁄₈" to 1³⁄₄"
2³⁄₈" or 2³⁄₄"
2¹⁄₈"
2¹⁄₈"
2¹⁄₈" Hole Saw
Tools Needed
2¹⁄₈" Hole Saw
5
If Needed, Enlarge Hole in Door Edge
If hole in door edge is smaller than 1", then use 1" drill bit to
enlarge hole.
1"
6
Check Strike (Door Jamb) Preparation
a. Place new strike box and strike against door jamb.
b. If strike box and strike do not fit properly, use pencil to trace
around strike box and strike and mark hole positions.
c. If needed, use chisel and drill to correct door jamb
preparation.
a
c
Pencil
OR
1"
b
BE365 DP existing holes Rev. 11/14-online
Chisel
© Allegion 2014
Printed in U.S.A.

Publicidad

loading

Resumen de contenidos para Schlage BE365

  • Página 1 BE365 Door Preparation Instructions For Door With Existing Holes Tools Needed Drill Bits Needed: 2¹⁄₈” Hole Saw Pencil Chisel ¹⁄₈”, ⁷⁄₈”, 1” Measure Door Width If Needed, Enlarge Hole in Door Edge If the door is thinner than 1³⁄₈” If hole in door edge is smaller than 1”, then use 1” drill bit to or thicker than 1³⁄₄”, then the...
  • Página 2 BE365 Door Preparation Instructions For Door With No Holes Mark and Drill Hole in Door Face with 2¹⁄₈” Hole Saw Tools Needed Tape Measure Pencil 2³⁄₈” or 2³⁄₄” Drill Bits Needed: ¹⁄₈”, ⁷⁄₈”, 1” 2¹⁄₈” Hole Saw Chisel 2¹⁄₈” Hole Saw Measure Door Width If the door is thinner than 1³⁄₈”...
  • Página 3 Measure 38” from finished floor and mark on door jamb. b. Mark center for strike hole exactly opposite latch hole. Door Jamb ¹⁄₈” Drill Bit 38” from Floor Latch Hole 38” From Floor © Allegion 2014 Printed in U.S.A. BE365 DP no holes Rev. 11/14-online...
  • Página 4: Keypad Locks

    Keypad Locks Cerraduras con teclado Verrous à claviers numériques Programming Guide Guía de programación Guide de programmation 23780034 Codes Códigos Codes Default Programming Code Código de programación Programming Code (Six Numbers) User Codes (Four Numbers) Código de programación (seis números) Códigos de usuario (cuatro números) Code de programmation (six chiffres) Codes d’utilisateur (quatre chiffres)
  • Página 5 • Cuando el modo de vacaciones esté activado, los códigos • Lorsque le mode vacance est activé, les codes d’utilisateur from the outside. • Esto tiene validez solo para el cerrojo con teclado (BE365). • S’applique uniquement au clavier numérique à pêne unlock the lock.