I - Door Reversibility - PURE EuroCave Modo De Empleo

4 - i
nstAlling youR Wine cABinet
Precautions (Continued)
•
For 1-temperature models only, place the humidity cartridge (located in
your cabinet's "accessories" bag) in the base of the cabinet, under the
grid, in the tray provided (see diagram below). When using for the first
time, immerse the entire cartridge in water for a few minutes to saturate
it then drain it thoroughly.
•
Install the stop (which is located in the accessories bag) at the back of
the cabinet (see diagram).
•
This allows a space of 7 cm
to be maintained between
the wall and the rear of the
cabinet. This spa
ce allows your cabinet's
power consumption to be
optimised.
•
Place the 2 caps in the 2
holes at the top of the
cabinet.
•
Do not push the caps all
the way in, in order to
allow the rear stop to be
installed.
•
Slide the rear stop between
the caps and the wall of the
cabinet, then push the 2 caps all the way in.
Installation
Place your cabinet in the desired location.
It must:
•
be open to the outside and well ventilated (not in an enclosed
cupboard, for example),
•
not be too damp (utility room, laundry room, bathroom...),
•
have a flat, stable floor,
•
be supplied with power (standard outlet, 16 A, earthed with 30mA*
circuit breaker). (* not applicable to some countries).
•
Place your cabinet in the desired location.
•
Fit the charcoal filter (located in the "accessories" bag) by inserting it
into the breather hole located on the top left-hand side of the inside of
your cabinet (see diagram below).
8
GB
•
Wait 48hrs before plugging in your cabinet
•
When using your cabinet for the first time, the charcoal filter alarm will
display. Reset the filter meter to 365 (see chapter 6, § VI).
Fig.1
Fitting the handle
(Full Glass and Black Piano doors only)
Fig.1
•
Unscrew the three screws placed on the side of the door, using the Allen
wrench, which you will find in the handle's box.
Fig.2
View from above
Seal
Handle
Front
Door frame
Fig.3
Figure 1
Fig.2
Figure 2
• Fig.3
Position the handle on the specially designed groove on the door frame
(figure 2).
•
Insert the handle all the way into the groove using a forward movement
(figure 2).
•
Screw the three screws back on (figure 3).
•
Take care not to catch the seal when screwing.
Note: adjustment of the handle is possible thanks to the oblong holes.
Door security
In order to make your cabinet secure, all doors have a lock.
Installing two cabinets side by side
N.B.: If you are placing two cabinets side by side, ensure that you leave a
gap of at least 1 cm between each cabinet.
Replacement of the LEDs on the control panel must
only be carried out by a qualified electrician.
Bottles must be arranged so that they do not come into contact
with the back wall. If this happens, the condensation created on
the wall may trickle onto the shelves and damage the bottle
labels. In addition, contact with the cold wall may create a frost point,
which is harmful to your wine.
I. Door reversibility
x3 x3
A B C
This allows you to change the direction in which the door opens. Follow
the instructions below (example for changing a right-hand door into a left-
hand door):
Figure 3
4
1
Unscrew the three screws using a "T25" Torx wrench.
2
Remove the upper hinge.
3
Carefully remove the caps using a thin blade.
4
Remove the cabinet door by opening it slightly, then lifting it upwards.
5
Unscrew the door pin.
6
Carefully remove the cap using a thin blade and assemble the pin in its
place. Reposition the cap on the opposite side
7
7
Unscrew the two screws and the door catch.
Unscrew the two screws on the opposite side and remove the two
washers.
- i
4
nstAlling youR Wine cABinet
x3 x4
A
Upper hinge
B
Caps
C
Caps
D E F G H J
D
Torx screw
E
Hex screw
x2
F
Door catch
G
Lower hinge
8
Mount the door catch on the desired opening side, using screws.
Replace the washers, then the screws, on the side opposite the door catch.
1
2
3
9
Turn the door through 180°.
Warning: the door is very heavy.
precautions to ensure that you do not injure yourself or drop it.
10
Put the door back on its pin.
8
11
Put in place the upper hinge.
12
Screw the hinge so that the door is completely parallel to the cabinet.
Check that the door seal adheres well to the cabinet (by closing the door),
to ensure that it is completely air-tight.
13
Put in place the caps.
H
Door pin
J
Door pin cap
Take any necessary
13
12
11
9
GB