Adler europe AD 7857 Manual De Uso página 6

PRODUCT DESCRIPTION: TOWER FAN AD7857 – look at figures 1 and 5
1.Front base
3.Base nut
5.Control panel LED display
7.Remote control
9.Rear air inlet grid
Control panel and remote control – look at figures 3 and 4
A. Power button
C. Speed control button
E. Timer button
G. Chosen speed indicator
H1. Normal mode indicator
H3. Sleep mode indicator
Assembling
1.The base of the tower fan consists of two parts (1,2), which fit around the main body (4) of the fan.
2.Turn the main body (4) of the device and the two parts of the base (1+2) upside down.
3.Loosen the base nut (3) so that you can attach the base (1+2), as illustrated at figure 1.
4.Attach one half of the base, making sure the power supply cord exits through the center hole in the base, then snap on the other half.
Secure the base (1+2) with the base nut (3), screwing it on tightly.
5.There are two sets of cut-outs underneath the base for the power supply cord. Guide the cord gently out of the base through one set of
cut-outs.
6.Turn the device the correct way up and place it on a flat and dry surface.
Operation
1.Place the tower fan on a dry, level indoor surface where it will not overturn during use. It is designed for floor use. Insert the power plug
into a separate electrical outlet. Do not use more than one electrical appliance at the same time on the same outlet.
2.For your convenience, the buttons on the control panel (6) on top of the device operate the same functions as the remote control (7).
Every press of a button will be acknowledged with a beep sound.
3.Press the power button (A) to switch on the device. It will start blowing air on the default settings: low speed and normal mode. Press
the power button (A) again to switch off the device.
4.Press the speed control button (C) repeatedly, to select the desired fan speed from three available options: low or middle or fast speed.
The indicator G will be illuminated on Control panel display (5) showing chosen fan speed.
5.Press the mode button (D), repeatedly, to select the desired style of fan flow named mode. For your choice are available 3 modes:
* NORMAL - fan operates at a constant speed chosen between: low or middle or high, the indicator H1 will be illuminated on Control
panel display (5).
* NATURAL - fan simulates a natural wind mode by cycling on and off, as in nature:
At low speed: the device is working 6 seconds and stop for 2 seconds and such cycles repeat all the time.
At middle speed: middle speed → stopped operation → low speed → middle speed → low speed → stopped operation → middle
speed → low speed ..., and such cycles repeat all the time. Each speed the working time is 6 seconds and stop 2 seconds.
At high speed: high speed → low speed → high speed → stopped operation → middle speed → low speed → high speed → middle
speed ..., and such cycles repeat all the time. Each speed the working time is 6 seconds and stop 2 seconds.
The indicator H2 will be illuminated on Control panel display (5).
* SLEEP - fan simulates gentle wind mode, suitable for rest time.
At low speed: no speed changes, always working in low speed.
At middle speed: middle speed working 30 minutes and turns down to low speed to always working in low speed.
At high speed: high speed working 30 minutes and turns down to middle speed to working 30 minutes also, and then turning to low
speed to always working in low speed.
The indicator H3 will be illuminated on Control panel display (5). All other indicators will shut off on the display after several seconds.
6.Press the oscillation button (B) to activate the oscillation function for widespread air flow distribution. The indicator (F) will be
illuminated on Control panel display (5). When the device is set to oscillate, press this button again to stop oscillation when the airflow is
in the desired direction.
7.Press the timer button (E) to set the timer function, the device will switch off automatically after a set time. Every repeated press of the
timer button (E) increases the set time by one hour, up to max. 12 hours. The indicator (J) will be illuminated on Control panel display (5)
to show desired time of operation before automatic shutting off. When timer function is not set up, the indicator (J) shows the current
ambient temperature is on the LED display (5).
REMARK: Handle the remote control (7) carefully, do not drop or throw it. For best signal reception, point the remote control (7) towards
the signal receiver at the top of the device. Ensure that nothing is obstructing the path of the signal.
Battery replacement
If the battery in the remote control (7) needs replacing, please replace it as follows: push the locking tab to one side and pull out the
battery holder, as illustrated at figure 2. Remove the old battery from the remote control (7) and insert a new one of the same type,
observing the battery polarity. Push the battery holder with the battery back into the remote control (7).
Cleaning and maintenance
CAUTION: Do not allow the main body (4) or any buttons to get wet.
1. Before cleaning remove the plug from the electrical socket.
2. To clean the main body (4) gently wipe it with a damp cloth, without detergents. Wipe dry.
3. To clean the rear air inlet grid (9) disassemble it follow up the figure 5:
First, unplug the device and unscrew the screw (8) at the back of the device. Next, take away the rear air inlet grid (9) by pulling it down
and towards you. Then, clean the grid (9) and inside wind rotor (10) by dry brush from dust. Assemble the grid (9) and screw (8) in
reverse order.
4. Store the device in a dry place.
Technical data:
Power 50W
2.Rear base
4.Main body
6.Control panel
8.Screw at the back side
10.Wind rotor
B. Oscillation button
D. Mode button
F. Oscillation function indicator
H. Chosen style / mode indicator
H2 .Natural mode indicator
J. Room temperature indicator / Timer indicator
Max Power 100W Voltage 220-240V~ 50Hz
6