Stanley FATMAX FME380 Manual Del Usuario página 12

ENGLISH
Any repair required on this laser product should be performed
by authorised service centre personnel.
Plunge cutting (fig.J)
Press button(10).
u
Switch on the tool.
u
Warning! The tool should run at full speed before the blade
enters into the workpiece.
Tilt tool forward with line-of-cut indicator (20) lined up with
u
desired line of cut marked on the workpiece. Gradually
move tool forward.
Warning! Never pull tool backwards.
Using the parallel guide (fig.K)
For making exact cuts along a workpiece edge.
u
Can be inserted in either side of foot.
u
Adjusting parallel guide
Loosen knob (5)
u
Adjust to desired cutting width by using parallel guide
u
scale (use line-of-cut indicator (20) as 0-reference).
Tighten knob (5).
u
Tips for optimum use
Only use sharp saw blades of the correct type and size
u
(fig. L).
Use hardened steel saw blade (17) for cutting wood,
u
aluminium, plastic and all sorts of laminated wood
Use diamond saw for (16) cutting ceramics and tiles
u
Use carbide-tipped blade (18) for wood and plastic only
u
Cutting large panels (fig. M)
Support panel close to the cut either on floor, table or
u
workbench.
Warning! Set cutting depth so that you cut through panel
and not through support.
In case parallel guide does not allow desired width of cut,
u
clamp or nail straight piece of wood to workpiece as a
guide, and use the right side of the foot against this guide.
Splinter-free cutting
Always face the good side of the workpiece down - fasten
u
a straight piece of wood on the workpiece by means of 2
clamps.
Cutting particularly tough or abrasive
materials
Soft sheet metal
Always set the depth adjustment to at least 1 mm deeper
u
than the material thickness to avoid the blade riding up
over the surface. Scrap material is required underneath
the work surface.
12
(Original instructions)
Remove burrs and rust as these impede the feed across
u
the material.
Thick beeswax (furniture polish) applied to the base plate
u
of the tool makes metal cutting easier.
Only suitable for cutting brass, copper, lead or aluminium.
u
Every 2 minutes of metal cutting should be followed by a
u
rest of at least 3 minutes.
Ceramic tiles, slates etc
Only use a blade specifically designed for this purpose.
u
Always use with a suitable vacuum cleaner or dust
u
extractor connected as the dust can be hazardous to the
operator and prevent the guard operating correctly.
Plasterboard:
The plunge saw is only recommended for making oc-
u
casional cut outs in plasterboard and always use it with a
suitable vacuum cleaner or dust extractor connected. The
dust can prevent the guard operating correctly.
Conventional tools such as keyhole saws or knives gener-
u
ally give excellent results, though the plunge saw can be
used if a particularly neat, dust free cut is required or if
there is a danger of cutting pipes or cables.
Maintenance
Your Stanley Fat Max corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
u
Do not use any abrasive or solvent-based cleaner.
Warning! If any of the following events occur during normal
operation, the power supply should be shut off at once and
tool thoroughly inspected by a qualified person and repaired
if necessary:
The rotating parts get stuck or speed drops abnormally
u
low.
The tool shakes abnormally accompanied by some
u
unusual noise.
The motor housing gets abnormally hot.
u
Heavy sparks occur around the motor area
u