Scan Mode - Miniland digimonitor 2.4 gold Manual De Instrucciones

ENGLISH
different areas with up to 4 cameras. To choose the
camera you want to see, follow the next steps:
1. Press the Menu/Back key
will pop up;
2. Press the UP or DOWN
icon is highlighted then press RIGHT key
into the sub-menu;
3. Press UP or DOWN
camera icon then press RIGHT
sub-menu;
4. Press RIGHT /LEFT
select the desired camera to view (Camera 1, camera
2, camera 3 or camera 4);
5. Press key go to selected cam;
Note: There is a faster way to change the camera you
are viewing. Directly press
paired cameras: CAM1 / CAM2 / CAM3 / CAM4 /

SCAN MODE.

5.2.9.1.2. SCAN MODE
This function automatically cycles through your paired
camera channels to display each camera for 12
seconds. This function can be used only when you
have more than 1 camera unit paired. To enter in this
mode:
1. Press the Menu/Back
pop up;
2. Press the UP key or DOWN
camera icon is highlighted then press RIGHT
enter into the sub-menu;
3. Press UP or DOWN
camera icon then press RIGHT
sub-menu;
4. Press RIGHT /LEFT
select the scan camera icon
5. Press key;
Note 1: When one of the cameras is out of range or is
not switch on, the monitor will warn you and the Scan
Mode will stop.
Note 2: The Scan mode can be turned on or off by
pressing the button while viewing the main screen.
5.2.9.1.3. DUAL MODE
The function will display two cameras on the screen at
the same time. It only can be used when there is more
than 1 camera unit paired.
1. Press the Menu/Back
pop up;
2. Press the UP key or DOWN
camera icon is highlighted then press RIGHT
enter into the sub-menu;
3. Press UP or DOWN
camera icon then press RIGHT
the sub-menu;
4. Press RIGHT /LEFT
select the dual view icon
5. Press key go to dual mode;
Note 1: At the dual view mode, you won't be able to
use the bidirectional function and you will hear only
the camera you have selected.
Note 2: A red frame will appear on the image
selected. To see the image of one of the two cameras
and the menu icon
key until the camera
to enter
key to select VIEW
key enter into the
/UP /DOWN key to
key to cycle through
key and the menu will
key until the
key
key to select VIEW
key enter into the
/UP /DOWN key to
;
key and the menu will
key until the
key
key to select VIEW
key to enter into
/UP /DOWN key to
;
full-screen, select with the RIGHT
which one you want to see and press
Note 3: If you have more than 2 cameras paired to
the same monitor, press RIGHT
which ones you want to see.
Note 4: When the Dual mode is turned on the VOX
and Standby modes cannot be used. The image will
not disappear from your screen.
5.2.9.1.4. ADD CAMERA AND PAIRING
The pairing between the monitor and the camera will
be done under two circumstances:
- If you want to add an additional camera.
- If the monitor and the camera are not paired.
The monitor and the original camera leave the factory
with channel 1 programmed, nonetheless, if for some
reason, they are not, you can link them manually
following the steps indicated below.
To pair the camera and the monitor follow the next
steps:
1. Press the MENU/Back
pop up.
2. Press the UP
camera icon is highlighted then press RIGHT
enter into the sub-menu.
3. Press UP key or DOWN
camera icon then press RIGHT key enter into
the sub-menu.
4. Press RIGHT /LEFT
select the desired camera to add.
5. Press key to search for a camera unit. The
power LED indicator (2) will begin to flash in green.
6. While the LED indicator is flashing, press the link
button on the camera (VI).
7. Once paired, the LED indicator will stop flashing
and the image of the camera will show immediately
on the monitor unit screen.
For various reasons you may lose the connection
between the monitor and a camera which is already
connected. Should this be the case, repeat the
process explained above to connect the camera with
the monitor again.
Note 1: Before starting the pairing process, make
sure that the camera and the monitor are close to
each other.
Note 2: Each camera can be linked just with one
monitor at a time.
Nota 3: If the monitor and the camera, for some
reason, have left the factory without being paired,
you will have to do it manually adding the camera to
channel 2, 3 or 4. You won't be able to pair the camera
again with channel 1 until you have paired it in another
channel and remove the channel 1 camera.
5.2.9.1.5. DELETE CAMERA
To delete one of the cameras connected, follow the
next steps:
1. Press the MENU/Back
will pop up.
2. Press the UP
camera icon is highlighted then press RIGHT
enter into the sub-menu.
3. Press UP key or DOWN
DELETE camera icon
22
and LEFT
key.
or LEFT
key and the menu will
key or DOWN key until the
key to select ADD
/UP /DOWN
key and the menu icon
key or DOWN key until the
key to select
then press RIGHT
key
to select
key
key to
key
key