Miniland digimonitor 2.4 gold Manual De Instrucciones página 25

First of all go to "Start Time" to set the time at which
you want the alarm to ring. For example, if you set the
Start Time to 12:00 p.m. and the alarm to ring every
4 hours (a total of 4 times), the first alarm will ring at
12:00 p.m, the second at 4 p.m, the third at 8 p.m and
the last at 12 a.m.
1. For the Start Time Setting: Press the LEFT
RIGHT key to select the item you want to set. Press
the UP key to increment and DOWN
down.
For the number of alarms per day Setting: Press
UP /DOWN key to select the option desired
between: One time each day/two times each day/
three times each day/four times each day. Press LEFT
or RIGHT key to select ON.
2. Press key to run the timer or press Menu/Back
key to exit without setting the alarm.
Note: Once the medicine alert is running, a dropper
icon (J) will be displayed on the LCD screen.
If you want to remove the alarm:
1. Press the Medicine alert key
Menu/Back key, Medicine alert setting screen will
be displayed.
2. Press UP /DOWN
want to remove.
3. Press the LEFT or RIGHT
4. Press key to confirm.
5.2.10.4.2. MEDICINE ALERT REVIEW
Press and hold the Medicine alert key
review screen pop up.
You can set or change the alerts already created by
following the steps on the section 5.2.10.4.1
At the review screen mode press the Menu/Back
key to exit.
Note 1: When the timer is ringing, press the Menu/
Back or key to stop it.
Note 2: If there is no answer, the ringing will last 1
minute and then stop, after 2 minutes the ringing will
be heard you again. The ringing will sound up to three
times;
5.2.11. eMyBaby
5.2.11.1 REGISTRATION
1. First of all register on the eMyBaby website. To do
so, open your browser, go to
www.emybaby.com and click on the CREATE
ACCOUNT tab.
2. Complete the fields with your personal data and
after having accepted the terms and conditions of use,
click on the ACTIVATE ACCOUNT tab.
3. You will receive a message of confirmation at
the e-mail address you provided in the registration
process. Clicking on the link containing the e-mail
message will take you back to the eMyBaby page,
where you need to enter your username and
password after clicking on the LOG IN tab.
5.2.11.2. IN ORDER TO VIEW THE IMAGE ON THE
PC TO WHICH THE BABY MONITOR
IS CONNECTED
1. In order to see the image transmitted by the camera
key to count
, then press the
key to select the alarm you
key to select OFF.
until the
on your PC, you should connect the monitor (screen)
to the USB port on your computer using a micro USB-
USB cable (not included). The monitor should be
switched on; if the battery is flat, recharge it.
2. After accessing eMyBaby using your username
and password, select the BABY MONITOR option in
DASHBOARD.
or 3. Now select the digimonitor 2.4" plus.
4. There are two options to choose from. Choose
"View only on the computer on which the monitor is
connected via the USB cable".
5. If everything is working correctly you should
automatically see your baby on the computer screen.
If there is a problem with the image, consult the
online viewing instructions by clicking on the READ
INSTRUCTIONS icon.
5.2.11.3. IN ORDER TO VIEW THE IMAGE AT A
DISTANCE BY MEANS OF eMyBaby
Follow the instructions below if you wish to view your
baby at a distance on your PC, tablet or Smartphone.
N.B: the monitor should be connected to your PC
in order to see the image captured by the camera
at a distance on eMyBaby. eMyBaby must transmit
a signal via the PC to which your baby monitor
screen is connected. If you do not follow this step
you will not be able to receive a signal on any
other appliance (PC, tablet or mobile device).
1. Connect the baby monitor to your PC in accordance
with the aforementioned steps, connecting the monitor
to the USB port on your computer using a micro USB-
USB cable (not included).
2. Access the eMyBaby (www.emybaby.com) website
using your username and password (register as
instructed above if you do not possess a username
and password) and select the BABY MONITOR
option.
3. Select the digimonitor 2.4" plus monitor from the
different models of baby monitor.
4. There are two options to choose from. Choose
"View from anywhere with an internet connection,
wherever you are, on another computer, tablet or
smartphone".
5. The first time you access this service you will be
asked to provide the product order number. This
number is displayed in the MNLXX-XXXXX (21)
format and is found inside the back of the monitor.
6. Entering this code will lead you to a screen
displaying two options: Emit and Receive signal. In
order to see the remote image captured on the camera
on your mobile device, click on the Emit button.
7. Then click on the
The following image will appear on your screen when
your computer begins to transmit:
Steps to follow if you wish to view the image from
another computer:
1. Connect the baby monitor to your PC in accordance
with the aforementioned steps, connecting the monitor
to the USB port on your computer using a micro USB-
USB cable (not included).
2. Access the eMyBaby website (www.emybaby.com)
using your username and password and select the
25
ENGLISH
icon in the center of the image.