Tabla de contenido
Publicidad
5� Mounting
• Check all components for damage.
• Do not use the product if it is damaged.
• Select an appropriate mounting location, taking
the reach and motion detection into considera-
tion. (Fig� 5�1)
• The most reliable way to detect movement is
given by mounting the light to point across the
direction in which people walk and by making
sure no obstacles (e.g. trees, walls etc.) interrupt
the line of sensor vision. (Fig� 5�2/5�3)
Mounting procedure
• Undo locking screw (Fig� 5�4) and detach enclo-
sure (B) from wall mount (C). (Fig� 5�4)
• Switch OFF power supply. (Fig� 5�5)
• Mark drill holes. (Fig� 5�5)
• Drill holes and fit wall plugs. (Fig� 5�6)
• Fit sealing plug.
– Power supply lead, concealed (Fig� 5�6)
– Power supply lead, surface-mounted (Fig� 5�7)
• Connect conductors. (Fig� 5�8)
• Fit enclosure onto wall mount. (Fig� 5�9)
• Screw in locking screw. (Fig� 5�9)
• Switch ON power supply. (Fig� 5�9)
6� Functions
Factory settings:
Time setting: 10 seconds
Twilight level: 1000 lux
All functions can be set after removing the ring
cover�
Time setting (stay-ON time) (Fig� 6�1/F)
The light's ON time can be set to any period from
approx. 10 seconds to a maximum of 15 minutes.
Any movement detected before this time elapses
will restart the timer.
Note: After the light switches OFF, it takes approx.
1 sec. before it is able to start detecting movement
again.
The light will only switch ON in response to
movement once this period has elapsed. The
shortest time setting is recommended when
adjusting the detection zone and performing the
functional test.
Twilight setting (response threshold) (Fig� 6�1/G)
The chosen response threshold can be infinitely
varied from approx. 2-1000 lux.
– Control dial set to
= daylight mode
(depending on ambient brightness)
– Control dial set to
= twilight mode
(approx. 2 lux)
The control dial must be turned to
when
adjusting the detection zone and performing the
functional test in daylight.
Please note:
Because the sensor has such a long reach, objects
heated up by sunlight (e.g. cars) may cause un-
wanted LED floodlight triggering when setting the
detection zone.
We therefore recommend setting the detection
zone at dusk.
Self-test
Once you have installed the wall mount and
connected the LED floodlight to the power supply,
it can be put into operation. The electronic system
now carries out a self-test which lasts for approx.
1 minute. Once this has been completed, the
sensor is active.
7� Reach adjustment
The detection zone can be optimised to suit re-
quirements. The shrouds supplied with the sensor
can be used to mask out as many lens segments
as you wish or shorten reach to suit the particular
situation. This prevents the light from being acti-
vated unintentionally, e.g. by cars, passers-by etc.
and allows you to target danger spots (Fig� 7�1).
The shrouds can be separated along the pre-
grooved divisions in the vertical and horizontal
directions or cut with scissors. After removing the
ring cover, the shrouds can be clipped on at the
top of the sensor lens. Now push the ring cover
back on again to hold the shrouds firmly in place
(Fig� 7�2-7�4).
The sensor housing can also be turned through
± 80° for precision targeting.
– 12 –
8� Operation/maintenance
The unit is not suitable for burglar alarm systems as
it is not tamperproof in the manner prescribed for
such systems.
Weather conditions may affect the way the LED
floodlight works. Strong gusts of wind, snow, rain
and hail may cause the light to come ON when it
is not wanted because the sensor is unable to dis-
tinguish between sudden changes in temperature
G B
and persons.
The detector lens may be cleaned with a damp
1
Y E A R
cloth if it becomes dirty (do not use cleaning
agents).
MANUFACTURER'S
WARRANTY
9� Disposal
Electrical and electronic equipment, accessories
and packaging must be recycled in an environmen-
tally compatible manner.
Do not dispose of electrical and electronic
equipment as domestic waste.
EU countries only:
Under the current European Directive on Waste
Electrical and Electronic Equipment and its imple-
mentation in national law, electrical and electronic
equipment no longer suitable for use must be
collected separately and recycled in an environ-
mentally compatible manner.
10� Manufacturer's Warranty
This STEINEL product has been manufactured with
the utmost care, tested for proper operation and
safety and then subjected to random sample in-
spection. Steinel guarantees that it is in perfect
condition and proper working order. The warranty
period is 36 months and starts on the date of sale
to the consumer. We will remedy defects caused
by material flaws or manufacturing faults. The war-
ranty will be met by repair or replacement of de-
fective parts at our own discretion. The warranty
shall not cover damage to wear parts, damage or
defects caused by improper treatment or mainte-
nance. Further consequential damage to other
objects shall be excluded.
Claims under the warranty will only be accepted
if the unit is sent fully assembled and well-packed
with a brief description of the fault, a receipt or in-
voice (date of purchase and dealer's stamp) to the
appropriate Service Centre.
Repair service:
If defects occur outside the warranty period or are
not covered by the warranty, ask your nearest ser-
vice station for the possibility of repair.
5
3
Y E A R
Y E A R
MANUFACTURER'S
MANUFACTURER'S
WARRANTY
WARRANTY
– 13 –
Publicidad
Tabla de contenido
