Bestway InflateYourFun HYDRO-FORCE 65046 El Manual Del Propietario página 10

Seat Board Installation
Slide the seat into position by inserting the flaps on both chamber of the boat into notches on the Seat Board. (FIG. 8)
Oars Installation
1. Join the two shafts of the oars together with the couplers and securely tighten the couplers covers. (FIG. 9)
Note: Completely insert the shafts into the Couplers or damage may occur.
2. Attach the oar blade to the end of the shaft and tighten the coupler.
3. Attach the oars to the oarlocks and lock them into position. (FIG. 10 & 11)
Note: When the oars are not in use, lock the oars into the Oar Clasps to avoid damage.
Outboard Motor Installation
With the boat fully inflated and in the water, attach your outboard motor onto Engine Mount at the center of the Transom.
Note:
-Ensure the motor is always fixed on the Transom.
-Read the instruction of outboard motor for correct installation and operation.
Storage
1. Remove the Oars from the oarlocks.
Note: Keep all accessories for future use.
2. Carefully clean the boat using a mild soap with clean water.
Note: Do not use acetone, acid, and/or alkaline solutions.
3. Do not dry the product in direct sunlight.
Note: Never dry with equipment such as electric blowers. Doing so will cause damage and shorten the boat's life span.
4. To deflate, open the Air Valves pushing the control stem in and rotating until the valves stay open. Deflate all the hull chambers at the same time so
the air-pressure drops together. This will prevent damage form occurring to the boat's inner structures.
5. Next deflate the Keel.
6. Fold the boat from front to back to remove additional air. You can also use a pump to drain any remaining air.
Caution
1. When landing on the shore, carry the boat. Do not tow it on the sand or ground as damage may occur.
2. If you use the tow rings to tow the boat, go slowly to avoid over-towing as damage may occur.
Safety Guideline
Follow all the Safety and Operating Instructions. If you don't follow this instructions, it may cause overturn, explode the boat and causes to drowning.
1. When using the boat, life saving devices such as life jackets and buoys should be pre-inspected and used at all times.
2. Before every use, carefully inspect all boat components including air-chambers, grab ropes, oars, and air valves, to ensure everything is in good
condition and tightly secured. Please stop to repair if you find any damage.
3. Buckets, water scoops and air pumps should always be available in case of air leakage or if the boat takes on water.
4. Passenger number and load weights shall by no means exceed specified capacities. Refer to the technical specifications section of this manual to
determine passenger numbers and load weights for your boat. Overweight will cause overturn and drowning.
5. When the boat is in motion, all passengers must remain seated at all times to avoid going overboard.
6. Use the boat near the shore and beware of natural factors such as wind, tide waters and tidal waves. Be aware of offshore winds and currents.
7. Be careful when landing on the shore. Sharp and rough objects such as rocks, cement, shells, glass, etc. may punctured the boat.
8. Bestway® inflatable boats are equipped with four air chambers (#65046 is two air chambers). If one chamber is punctured when the boat is in the
water, it may be necessary to fully inflate the other air chamber to prevent the boat from sinking.
9. To avoid damage do not drag the boat on rough surfaces.
10. Don't leave the boat exposed to sun for long periods of time, as high temperatures shall give rise to air expansion, which can cause irreparable
damage.
11. When choosing an outboard motor, refer to the technical specifications section of this manual to determine acceptable horsepower ratings.
12. For electrical motors equipped with batteries, note that battery acid can be caustic, which can cause damage to both skin and boat materials.
13. For motors use fuel such as gas, oil, petrol, since fuel is a flammable substance and should be kept away from open flames. Further, clean the boat
material immediately if fuel spatters onto the boat surface.
14. Inflate according the numbered air chamber and rated pressure on the boat, or it will cause over inflation and boat explosion.
15. All loads placed in the boat should be distributed evenly for proper boat trim. Keep the boat balanced. Uneven distribution of persons or load in the
boat may cause overturn the boat and drowning.
16. Be responsible, do not neglect the safety rules, this could jeopardize your life and the lives of others.
17. Follow these instructions to avoid drowning, paralysis or other serious injuries.
Repairs
1. If there is a leak, spay water onto the boat's surface and look for air bubbles. Soapy water works well.
2. Using the provided heavy-duty repair patch, dry the damaged area, apply the vinyl cement and stick the repair patch into place.
Smooth out any air bubbles.
10
S-S-000907