TZS First AUSTRIA FA-5140-2 Manual De Instrucciones página 3

MEAT GRINDER
INSTRUCTION MANUAL
DESCRIPTION
(fig. A)
1. control panel
2. Locking knob
3. head inlet
4. head
5. hopper plate
6. Food pusher
7. snake
8. Cutting blade
9. Cutting plate (fine)
10. Cutting plate (medium)
11. Cutting plate (large)
12. Fixing ring
13. Kibbe attachment
14. Sausage attachment
a) Sausage attachment (fine)
b) Sausage attachment (medium)
c) Sausage attachment (large)
15. Body
IMPORTANT SAFEGUARD
• Home use only. Do not use for industrial
purpose.
• Unplug when assembling and
disassembling the unit.
• Close supervision is necessary when any
appliance is used near children.
• When carrying the unit be sure to hold the
head with one hand, and the back knob
with the other hand. Do not carry the unit
by the hopper plate or head.
• Do not fix the cutting blade and cutting
plate when using kibbe attachment.
• To avoid jamming, do not force to operate
the unit with excessive pressure.
• Never try to replace the parts and repair
the unit by yourself.
• Never push products by hand. Use food
pusher.
• Do not grind hard food such as bones,
nuts, etc.
• Do not grind ginger and other materials
with hard fiber.
• Continuous work cycle for 10 minutes,
automatic stop. Cooling after 10 minutes,
can continue to operate
• If the machine to "work" - "reverse" or
"reverse work" the operation, must be in a
previous work stop 5 seconds or older to
reverse direction operation. Otherwise the
key operate no action.
M_5140-2_v02.indd 2-3
• When the machine didn't work properly.
The machine will automatically be
reversed five seconds or so stop after,
remove blocked, can continue to work.
• If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent or similarly qualified persons in
order to avoid a hazard.
• Switch off the appliance and disconnect
from supply before changing accessories
or approaching parts that move in use.
• Do not operate this appliance if the cord
or plug is damaged. Return it to the
store of service or repair by professional
serviceman.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for their
safety.
• Children should be supervised to ensure
that they do not play with the appliance.
BEFORE ThE FIRST USING
• Check that voltage indicated on the rating
label corresponds the mains voltage in
your home.
• Wash all parts (except body) in warm
soapy water.
INSTRUCTION FOR USING
ASSEMBLING
• For the direction of arrow and put the
Head into the wave box (fig. 1). Then use
the right hand clockwise handle, when
spin in place, not in turn. Explain lock.
(fig. 2).
• Place the snake into the head, long end
first, and turn to feed the screw slightly
until it is set into the motor housing
(fig. 3).
• Place the cutting blade onto the snake
shaft with the blade facing the front as
illustrated. If it is not fitted properly, meat
will not be ground (fig. 4).
• Place the desired cutting plate next to the
cutting blade, fitting protrusions in the slot
(fig. 5).
• Support or press the centre of the cutting
plate with one finger then screw the fixing
ring tight with another hand (fig. 6). Do not
over tighten.
2
• Place the hopper plate on the head and fix
it into position.
• Locate the unit on a firm place.
• The air passage at the bottom and the
side of the motor housing should be kept
free and not blocked.
MINCING MEAT
• Cut all foods into pieces so that they fit
easily into the hopper opening.
• Ground meat by pressing the „І" low gear
or „II"-high-speed file.
• Feed foods into the hopper plate. Use for
it only the food pusher (fig. 7).
• After use press the „OFF" button that stop
and pulled the plug.
REVERSE FUNCTION
• If the clogging, the machine will
automatically be reversed or press
the „REV" key, the machine reversal 5
seconds.
• Snake will reverse rotation, plug will be
lifted.
• Remove jam, disconnect the power plug,
head of the food in the clear.
MAKING KIBBE
• Mince meat three times and mix all
ingredients together in a bowl. More meat
and less flour for outlet cover create better
consistency and taste.
• Grind the mixture three times.
• Disassemble by reversing the steps form
assembling 5-3 to remove the cutting plate
and cutting blade
• Place kibbe attachments A and B onto
the feed screw shaft together, fitting
protrusions in the slots. (fig. 8)
• Screw cap into place until tight. Do not
over tighten (fig. 9).
• Make the cylindrical outlet cover (fig. 10).
• Form kibbe as illustrated below and deep
fry.
SAUSAGE ATTAChMENT
(see fig. 11)
3
CLEANING AND MAINTENANCE
DISASSEMBLING
• Make sure that the motor has stopped
completely.
• Disconnect the plug from the power outlet.
• Disassemble by reversing the steps from
assembling.
• To remove the cutting plate easily, place a
screwdriver between the cutting plate and
the head as illustrated and lift it up (fig. 12).
• Press the fasten knob, move the head as
per direction illustrated on (fig. 13), then
you can take out the head.
CLEANING
• Remove meat, etc.
• Wash each part in warm soapy water.
• A bleaching solution containing chlorine
will discolor aluminum surfaces.
• Do not immerse the motor housing in
water, but only wipe it with a damp cloth.
• Thinners and petrol will crack of change
the color of the unit.
• Wipe all the cutting parts by vegetable oil-
wet cloth.
SPECIFICATION
Rating: 220-240V, 50Hz
total Electric
absorber Power: 700W, 1800W max
12-10-26 上午9:09