Resetting To Factory Settings - Vimar ELVOX 1200 Serie Instrucciones Instalador

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 22
-
Pressing the OK button returns to the first two digits of the ver-
sion. Pressing the ESC button returns to the previous menu.

RESETTING TO FACTORY SETTINGS

Resetting the device deletes all of the data stored in memory. The security
code is reset to 99, the internal and internal units will no longer be paired.
- Enter the security code as indicated in the paragraph "ENTERING THE
SECURITY CODE"
PERFORMING THE RESET
- Press the > button until "rr" is displayed
- Press the OK button
- Enter the first digit of the security code using the < and > buttons
- Press the OK button
- Enter the second digit of the security code using the < and > buttons
- Press the OK button
- Two red dots then appear on the display. The scanner flashes orange.
The device is now restored to its original settings.
- To start operating the device again, see the section "Initial startup: Pairing
the control unit with the fingerprint scanner".
3. Fingerprint scanner
Operating the fingerprint scanner
Correct operation of the fingerprint scanner is a guarantee that the product
will function properly. We recommend that you use the finger which has
the best fingerprint lines in your opinion. It is also recommended to swipe
your finger over the sensor while applying a medium amount of pressure.
In particular with poorly pronounced finger lines, you should avoid pressing
down too hard on the sensor and squashing the finger lines, so as to ensure
correct identification. The scanner is equipped with an automatic Learning
Finger system to improve recognition performance over a long period. To
optimise recognition of the fingerprint, it is best to swipe the finger over the
sensor at least 5 times. If any negative identification results are returned,
we recommend that you repeat the enrolment process for that finger. In the
event of insufficient fingerprint identification, try the following:
-
Apply less pressure on your finger when you place it over the sensor.
-
Make sure that you place your finger exactly over the finger area visible
on the casing
-
Use the pad of your finger starting from the top knuckle. The joint be-
tween the first and second sections of your finger should be the start
position for scanning.
-
The middle finger is typically the best finger for scanning.
-
Avoid using the small finger or thumb as they are difficult to position on
the scanner. Thumbs are the most difficult to use.
-
Try scanning the fingerprint at different speeds to find out the best speed
for you.
Do not exaggerate the movement, if it is too slow or too fast the finger will
not be identified.
If the above information does not help, we recommend that you save the
same fingerprint in several positions to improve the recognition rate. The
device has space for 99 fingerprints! In extreme cases use up to 10 memory
spaces for one finger. Wet fingers show modified finger lines, as can be seen
with the naked eye. If you often have wet fingers we advise you to save a wet
version of your fingerprint. Children's fingerprints are usually only recognised
from the age of 5, depending on the child's height. Please also observe the
points mentioned above.
EN
ENROLLING A FINGERPRINT USING THE SENSOR
It is important to swipe your finger correctly over the sensor.
!
Best results are achieved by using the middle finger while stretch-
ing out the middle finger and ring finger at the same time.
Swipe the desired finger, starting from the top knuckle, making full contact
with the sensor. The larger the scanned surface of the finger, the higher the
recognition rate. In order to maximise the recognition rate, swipe your finger
along the sensor in the same way as in the enrolment process.
The sensor is located in the middle of the finger swiping track.
Swipe the finger carefully, with light pressure and constant, moderate
speed over the sensor.
In the case of excessively worn fingerprint patterns caused by manual work,
we recommend, for instance, that right-handed people enrol a fingerprint
from their left hand. If the lines of your fingerprint are difficult to see, use a
finger where the lines are most pronounced.
WARNING!
Try to swipe as large a surface as possible over the sensor, starting
from the top knuckle, with moderate pressure and speed. This ensures
the best recognition results.
9

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Elvox 12adElvox 12a0Elvox 12a1Elvox 12a2Elvox 12a3Elvox 12a4

Tabla de contenido