Declaration Of Conformity - Bosch GOF Professional 900 CE Manual Original

Ocultar thumbs Ver también para GOF Professional 900 CE:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 40
OBJ_BUCH-203-003.book Page 23 Tuesday, September 2, 2008 8:46 AM
An estimation of the level of exposure to vibra-
tion should also take into account the times
when the tool is switched off or when it is run-
ning but not actually doing the job. This may sig-
nificantly reduce the exposure level over the to-
tal working period.
Identify additional safety measures to protect
the operator from the effects of vibration such
as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.

Declaration of Conformity

We declare under our sole responsibility that
the product described under "Technical Data" is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Dr. Eckerhard Strötgen
Senior Vice President
Head of Product
Engineering
Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
31.07.2008
Assembly
Inserting a Router Bit (see figure A)
Before any work on the machine itself, pull
the mains plug.
It is recommended to wear protective
gloves when inserting or replacing router
bits.
Depending on the application, router bits are
available in the most different designs and qual-
ities.
Bosch Power Tools
Router bits made of high speed steel (HSS) are
suitable for the machining of soft materials, e. g.
softwood and plastic.
Carbide tipped router bits (HM) are particular-
ly suitable for hard and abrasive materials, e. g.
hardwood and aluminium.
Original router bits from the extensive Bosch ac-
cessories program are available at your special-
ist shop.
Only use clean router bits that are in perfect
condition.
– Fold the chip shield 6 down.
– Push the spindle lock lever 4 in clockwise di-
rection and hold it in this position ( ). If re-
quired, turn the motor spindle by hand until
it is locked.
– Loosen the tightening nut 23 with the open-
end spanner 25 (size 24 mm) by turning in
antclockwise direction ( ).
– Insert the router bit into the collet. The shank
of the router bit must be immersed at least
20 mm into the collet.
– Tighten the tightening nut 23 with the open-
end spanner 25 (size 24 mm) by turning in
clockwise direction. Release the spindle lock
lever 4.
– Fold the chip shield 6 up again.
Do not insert a router bit with a diameter
larger than 50 mm when the guide bushing
is not mounted. Such router bits do not fit
through the base plate.
Do not tighten the tightening nut of the col-
let without a router bit inserted. Otherwise
the collet can be damaged.
Dust/Chip Extraction (see figure B)
Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one's health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
English | 23
1 609 929 N93 | (2.9.08)

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Gof professional 1300 ce

Tabla de contenido