Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Customer Assistance - Bosch GHG 660 LCD Professional Manual Original

OBJ_BUCH-485-005.book Page 15 Monday, May 14, 2012 9:28 AM
Placing Down the Power Tool (see figure C)
To cool down the power tool or have both hands free, place it
down on the standing surface 1.
Be especially careful when working with the placed
down power tool! There is danger of burning oneself on
the hot nozzle or on the hot air jet.
Work Examples
The illustrations of the work examples can be found on the
fold-out pages.
The temperature settings in the work examples are reference
values that can vary, depending on the material characteris-
tics. The distance between the nozzle and the workpiece de-
pends on the material to be worked.
The optimal temperature for the respective application can be
determined by practical testing. Always start with a low tem-
perature setting.
All application examples can be performed without accesso-
ries except for "Removing Varnish/Paint from Windows".
However, the use of recommended accessories simplifies the
work and significantly improves the quality of the result.
Be careful when changing the nozzle! Do not touch the
hot nozzle. Allow the power tool to cool down and wear
protective gloves while changing the nozzle. Danger of
burning oneself on the hot nozzle.
Removing Varnish/Softening Adhesives (see figure A)
Mount the wide jet nozzle 11 (accessory). Briefly soften the
varnish applying hot air and remove it using a sharp, clean
scraper or putty knife. Applying heat too long will burn the var-
nish, making it more difficult to remove.
Many adhesives (e.g. of stickers) become soft when heated.
Heated adhesives allow for bonds to be separated or exces-
sive adhesive to be removed.
Removing Varnish/Paint from Windows (see figure B)
Use of the glass protection nozzle 12 (accessory) is es-
sential. Danger of glass breaking.
On profiled surfaces, varnish can be removed using an appro-
priately fitting spatula and brushed off with a soft wire brush.
Shaping Plastic Tubing (see figure C)
Mount the reflector nozzle 13 (accessory). To avoid kinking of
the tubing, fill the tubing with sand and plug both ends. Heat
the tubing evenly by by applying the heat from side to side.
Welding Plastics (see figure D)
Mount the reduction nozzle 16 and the welding shoe 15 (both
accessories). The workpieces to be welded and the welding
rod 14 (accessory) must be of the same material (e.g. both of
PVC). The seam must be clean and grease-free.
Carefully heat up the seam location until it becomes doughy.
Please note that the temperature difference between the
doughy and liquid state of plastic is low.
Feed in the welding rod 14 and allow it to run into the gap so
that a uniform bead is produced.
Bosch Power Tools
Shrinking (see figure E)
Mount the reduction nozzle 16 (accessory). Select the diam-
eter of the heat-shrinkable sleeve 17 (accessory) according
to the workpiece (e.g. a cable lug). Heat the heat-shrinkable
sleeve evenly.
Defrosting Water Pipes (see figure F)
Before heating pipes, check to make sure that it is actu-
ally a water pipe. Water lines often do not differ in appear-
ance from gas lines. Gas lines are not to be heated under
any circumstances.
Place on the angle nozzle 18 (accessory). Heat the frozen
zone always from the outside to the middle.
Heat up plastic pipes as well as connections between pipe
pieces especially careful to prevent damage.
Soft Soldering (see figure G)
For point soldering, place on the reduction nozzle 16, for the
soldering of pipes/tubing, place on the reflector nozzle 13
(both accessories).
If solder without flux is used, apply soldering grease or paste
to the location to be soldered. Warm the location to be sol-
dered for 50–120 seconds depending on the material. Apply
the solder. The solder must melt from the workpiece temper-
ature. After the soldered location has cooled, remove the flux.

Maintenance and Service

Maintenance and Cleaning

Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Cleaning the Coarse-debris Filter
Pull the cover with coarse-debris filter 2 toward the rear out of
the housing. Blow out the filter (e.g. with compressed-air) or
clean it with a soft brush. Reattach the cover with coarse-de-
bris filter.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.

After-sales Service and Customer Assistance

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Our customer service representatives can answer your ques-
tions concerning possible applications and adjustment of
products and accessories.
English | 15
1 609 929 W90 | (14.5.12)