1. Manuales
  2. Marcas
  3. Metra Manuales
  4. Accesorios de Automóviles
  5. 99-7629S
  6. Instrucciones de instalación

Metra 99-7629S Instrucciones De Instalación

Ocultar thumbs
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Descargar este manual
Nissan Armada/Titan w/ Factory NAV 2004-2007
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted to match factory dash panel
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (10) #8 x 3/8" Phillips screws • E) (6) Panel clips
• F) Rear A/C delete plugs
A
B
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-7550
Antenna Adapter: • Not required
METRA. The World's best kits.
Installation instructions for part 99-7629S
99-7629S
C
D
metraonline.com
™
Dash Disassembly ................................................. 2
Kit Preparation ....................................................... 3
Kit Assembly
– ISO DIN radio provision with pocket ...................... 3
–
ISO DDIN radio provision ...................................... 4
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Torx T-10 driver
E
CAUTION!
tery terminal before beginning any installation, unless the vehicle
F
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con -
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
Table of Contents
Metra recommends disconnecting the negative bat -
© COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION

Publicidad

Tabla de contenido
loading

Manuales relacionados para Metra 99-7629S

Resumen de contenidos para Metra 99-7629S

  • Página 1 • Torx T-10 driver • F) Rear A/C delete plugs CAUTION! Metra recommends disconnecting the negative bat - tery terminal before beginning any installation, unless the vehicle manufacturer recommends against so. Please check with your local Dealership for more information. All accessories, switches, climate controls panels, and especially air bag indicator lights must be con - WIRING &...

  • Página 2: Dash Disassembly

    Note: The small round sticker also T-10 TORX T-10 TORX HAZARD SWITCH SCREW SCREW needs to be removed from the factory panel and placed onto the 99-7629S radio trim panel. (Figure D) (Figure A) Continue to kit preparation (Figure C)

  • Página 3: Kit Preparation

    99-7629S Kit Assembly Kit Preparation To the 99-7629S radio trim panel: ISO DIN radio provision with pocket 1. Attach the factory climate controls using 1. Secure the radio brackets to the (4) #8 X 3/8” Phillips screws supplied. pocket using (4) #8 x 3/8” Phillips (Figure A) screws supplied.

  • Página 4: Important

    Before doing so, look over the instructions a in the dash, and complete all necessary connections to second time, and make sure the installation the radio. Metra recommends using the proper mating was performed exactly as the instructions adapter from Metra and/or AXXESS. Re-connect the are stated.

  • Página 5: Características Del Kit

    Instrucciones de instalación para la pieza 99-7629S Indice Nissan Armada/Titan w/ Fábrica NAV 2004-2007 Desmontaje tablero ..........2 99-7629S Preparación del kit ..........3 Ensamble del kit – Provisión de radio ISO DIN con cavidad ....3 CARACTERÍSTICAS DEL KIT •...

  • Página 6: Desmontaje Tablero

    SCREW SCREW Nota: La pequeña pegatina redonda también tiene que ser retirado del panel de la fábrica y (Figura D) (Figura A) se coloca en el 99-7629S panel de moldura de radio. Continúe con la preparación del kit (Figura C)

  • Página 7: Preparación Del Kit

    Ensamble del kit Preparación del kit Provisión de radio ISO DIN con cavidad Para el 99-7629S panel de moldura de radio: 1. Coloque los controles de clima de fábrica 1. Asegure los soportes de radio en el usando (4) #8 x 3/8” tornillos Phillips bolsillo usando (4) #8 x 3/8”...

  • Página 8: Importante

    Metra recomienda que use adaptadores adecuados instalación se haya realizado exactamente de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la como se indica en las instrucciones. Por terminal negativa de la batería y pruebe el radio para verificar favor tenga el vehículo desarmado y listo...

Tabla de contenido