Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
STEEL ASSEMBLY TABLE
TOOLS NEEDED
9/16" Wrench
5/8" Wrench
10 mm Wrench
IMPORTANT! For mobile tables, use assembly
instructions included with the caster kit.
HARDWARE INCLUDED
• (4) 3/8" x 3" Bolts
• (4) 3/8" Flange Nuts
STARTER TABLE
NOTE: Install all bolts and nuts prior to tightening.
1.
Unfold leg assemblies. (See Figure 1)
Figure 1
2. Unfold flat braces and line up with holes in leg
assemblies. Install to leg using 3/8" x 3" bolts and
nuts. (See Figure 2)
Figure 2
3/8" x 3" Bolts
and Nuts
Flat Brace
PAGE 1 OF 9
1-800-295-5510
uline.com
Phillips Screwdriver
NOTE: Tables longer than 72" include two boxes:
one starter table and one add-on table.
ASSEMBLY
ADJUSTING TABLE HEIGHT
1.
Remove pre-installed leg bolt and adjust leg to
desired table height. Reinstall leg bolt and nut.
(See Figure 3)
NOTE: When adjusting to the lowest height
setting, the flat brace bolts must be removed
from the leg assemblies. Reinstall flat brace
bolts after leg bolts are inserted.
Figure 3
Desired
Table
Height
2. With the aid of a helper, turn table upright.
(See Figure 4)
Figure 4
3. If the table is a stand-alone table, all nuts can be
tightened fully.
NOTE: Do not tighten if add-on tables
will be attached.
For assembly of add-on tables and table with shelf,
see page 2.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
Leg Bolt
Leg Bolt
1021 IH-3630
Publicidad
Tabla de contenido
Manuales relacionados para Uline H-3630
Resumen de contenidos para Uline H-3630
- Página 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. 1-800-295-5510 uline.com STEEL ASSEMBLY TABLE TOOLS NEEDED 9/16" Wrench Phillips Screwdriver 5/8" Wrench 10 mm Wrench IMPORTANT! For mobile tables, use assembly NOTE: Tables longer than 72" include two boxes: instructions included with the caster kit.
-
Página 2: Hardware Included
ADD-ON TABLE ASSEMBLY Figure 5 (2) 3/8" x 3/4" Bolts Starter Add-On and Nuts Table Table Flat Brace Starter Leg Brace Bolt HARDWARE INCLUDED 3. Unfold remaining flat braces on add-on table and line up with leg assembly on starter table. •... - Página 3 M6 flat washers using a 10 mm wrench and Phillips table, add-on table and starter table shelf screwdriver. (See Figure 8) have been fully assembled and all bolts and nuts are tightened. Figure 8 Cross Bar 1-800-295-5510 uline.com PAGE 3 OF 9 1021 IH-3630...
- Página 4 800-295-5510 uline.mx MESA DE ACERO PARA ENSAMBLE HERRAMIENTAS NECESARIAS Llave de 9/16" Desarmador de Cruz Llave de 5/8" Llave de 10 mm ¡IMPORTANTE! Para mesas portátiles, utilice las NOTA: Las mesas más largas de 72" incluyen instrucciones incluidas en el kit de ruedas.
-
Página 5: Ensamble De La Mesa Complementaria
ENSAMBLE DE LA MESA COMPLEMENTARIA 2 Pernos de 3/8" x 3/4" Diagrama 5 Mesa Mesa y Tuercas Complementaria Básica Soporte Plano Perno del Soporte de la Pata Inicial TORNILLERÍA INCLUIDA 3. Desdoble los soportes planos de la mesa complementaria y alinéelos con el ensamble de •... -
Página 6: Ensamble De Repisa Complementaria
M6 usando tuercas apretados. una llave de 10 mm y un desarmador de cruz. (Vea Diagrama 8) Diagrama 8 Barra Transversal 800-295-5510 uline.mx PAGE 6 OF 9 1021 IH-3630... -
Página 7: Outils Requis
1-800-295-5510 uline.ca TABLE D'ASSEMBLAGE EN ACIER OUTILS REQUIS Clé de 9/16 po Tournevis cruciforme Clé de 5/8 po Clé de 10 mm IMPORTANT! Reportez-vous aux instructions REMARQUE : Les tables longues de plus de 72 ARRÊT fournies avec l'ensemble de roulettes pour le po sont réparties en deux boîtes : une table de... -
Página 8: Matériel Inclus
MONTAGE DES TABLES COMPLÉMENTAIRES 2 boulons et écrous Figure 5 Table de 3/8 po x 3/4 po Table de base complémentaire Barre de renfort Boulon de barre de renfort de la table de base MATÉRIEL INCLUS : 3. Dépliez les barres de renfort de la table complémentaire et alignez-les avec les pattes de •... -
Página 9: Montage De Tablette Complémentaire
M6 à l'aide d'une clé de 10 mm et d'un et écrous. tournevis cruciforme. (Voir Figure 8) Figure 8 Barre transversale 1-800-295-5510 uline.ca PAGE 9 OF 9 1021 IH-3630...