Midland PMR446 Manual De Instrucciones página 14

SETTING THE CLOCK MODE
When BASE CAMP is off, the display shows the current time setting.
To visualize the clock while the radio is on, just turn the POWER/VOL knob on off.
To change the hour setting of the clock:
LOCK/CALL/HOUR button, and the hour digit of the clock will blink.
- Press the
- Turn the TUNING knob to change the hour setting.
- To confirm, press the PTT/SELECT button or wait for 5 seconds.
To change the minute setting of the clock:
- Press the SCAN/MINUTE button while in CLOCK mode and the minute digit of the clock will
blink.
- Turn the TUNING knob to change the hour setting.
- To confirm, press the PTT/SELECT button or wait for 5 seconds.
SETTING THE ALARM CLOCK
BASE CAMP can also function as an ALARM CLOCK.
To turn the ALARM CLOCK on:
Press the MONITOR/ALARM ON/OFF button while in CLOCK mode, the ALARM CLOCK icon
will appear on the display.
To set the hour setting of the ALARM, press the LOCK/CALL/HOUR button while in CLOCK mode
and the hour digit of the clock will blink. Turn the TUNING knob to change the hour setting. To
confirm, press the PTT/SELECT button or wait for 5 seconds.
To set the minute setting of the ALARM, press the SCAN/MINUTE button while in CLOCK mode,
and the minute digit of the clock will blink. Turn the TUNING knob to change the minute setting.
To confirm, press the PTT/SELECT button or wait for 5 seconds.
To turn the ALARM CLOCK off:
To disable the alarm clock, press the MONITOR/ALARM ON/OFF button while in CLOCK mode.
will disappear.
Instead, if you press the MENU/MONITOR/SCAN-LOCK-CALL button, the alarm clock icon will
still be displayed, but the alarm will ring the day after at the same time, that is, after 24 hours from
the pre-setting alarm time.
Setting the alarm clock snooze
When the ALARM CLOCK goes off, you can activate the SNOOZE function by pressing the PTT/
SNOOZE button. Every time the SNOOZE button is pressed the ALARM CLOCK will go off again
after 8 minutes.
USING THE FLASHLIGHT
BASE CAMP has a built-in FLASHLIGHT.
To turn the FLASHLIGHT ON, set the LIGHT switch to "on".
To turn the FLASHLIGHT OFF, set the LIGHT switch to "off".
MORSE CODE
BASE CAMP can send Morse code.
When the radio is on AM/FM/MARINE BAND, pressing the MENU button more time it's possible
to send Morse signals.
USB JACK
MIDLAND BASE CAMP can be used to charge a mobile phone, iPod, mp3 player by the DYNA-
MO CRANK, AC or DC Adapter thru the USB jack.
• Attach a USB charging cable (optional) to the USB jack of the MIDLAND BASE CAMP;
• Connect the other end of the USB charging cable to the mobile phone, mp3 or iPod;
• Recharge the mobile phone battery, the mp3 or the iPod by turning rapidly the DYNAMO
CRANK, or by connecting the AC or DC Adapter into the Charging jack.
RECHARGING THE BATTERY PACK
MIDLAND BASE CAMP is equipped for using a 6V NiMH rechargeable battery pack which can be
recharged using an AC wall adapter (included) or a DC adapter (included).
Initial charge time is 12 hours with a charge time of 8/10 hours thereafter.
For maximum battery life, we recommend charging the battery pack when the BASE CAMP is off
and the low battery icon comes on.
To recharge the battery pack you need to connect the socket of the wall adaptor to a mains power
socket and insert the jack of the wall adaptor into the charging jack of the BASE CAMP.
Remove MIDLAND BASE CAMP from the charger only when the charge time expires.
You can also charge the rechargeable NiMH battery pack using the Dynamo crank. To charge using
the Dynamo Crank rotate rapidly the Dynamo Crank handle clockwise or counter-clockwise.
WARNING
! The supplied wall charger is using "standard charging" method. This is a method, whe-
re the charging current is about 10 % of the capacity and the batteries will be charged
over night or within 10-14 hours. Using this method, chargers do not automatically
disconnect charging when batteries are fully charged. It does not matter if you let the
charger connected from time to time longer than necessary, but you should avoid to
- 14 -