Lutron Hi-lume L3D0-96W24V-U Instalación

Hi-lume Premier 0.1% EcoSystem
®
Installation
041562 Rev. A
07/2016
L3D0-96W24V-U UL Listed Driver
®
Output: 25–96 W 24 V- Input: 120–277 V~ 50 / 60 Hz, Max 110 W
Important Notes: Please read before installing.
• For installation by a qualified electrician in accordance with all local and national electrical codes.
• Use copper conductors only.
• For indoor use only.
• For 277 V~ applications, a suitable barrier may be required between the non-Class 2 and Class 2
wiring, per local and national electrical wiring codes. For your convenience, the driver includes an
optional barrier.
• Check to see that the driver type and rating are suitable for the application.
• DO NOT install if product has any visible damage.
• If moisture or condensation is evident, allow the product to dry completely before installation.
• Operate between 32 °F (0 °C) and 104 °F (40 °C) ambient.
• 0% to 90% humidity, non-condensing.
• Four 8-32 × 3/8 in (9.5 mm), serrated lid screws provided.
• For best practices, please refer to Application Note #591 (P/N 048591) at www.lutron.com
Required Components
For each system, ensure that you have:
One Compatible At least one Hi-lume
1,2
Lutron Control Premier 0.1% Driver
®
At least one compatible
LED Load (light engine) 3
1
See list of compatible controls on the reverse side.
2 Please refer to the control installation sheet for wiring instructions.
3
Refer to LED load manufacturer instructions for proper installation practices.
Load ratings must match driver output ratings.
Lutron Electronics Co., Inc. | 7200 Suter Road | Coopersburg PA, 18036-1299
/ 3-Wire Voltage LED Driver
TM
English
®
om 0.1 %
lutr on.c Pre mi er
Hi- lum e
TM
6W 24V -U
L3D 0-9 Drive r
ge LED
Fade -to-B lack TM tant Volta
Soft- on, 3-wir e Cons
pour DEL
EcoS ystem TM u au noir
doux , fond tensi on cons tante
Allum age Pilote 3-fil 4.577 .7661 )
EcoS ystem TM .LUT RON 1 (1.84
da: 1.844
USA / Cana
W Max
A 110
e: 0,92 - 0,40
Input | Entré / 60 Hz
V ~ 50
120 - 277
| Sorti e:
Outp ut Class 2
4 A Max
24,0 V
tmen t Knob Sorti e
ut Adjus Bass e de
Light Outp l'Extr émité
Low End age pour
de Régl
Bout on
ère
de Lumi
wire only. ment .
- 12 AWG mm² seule
Use 20 0,50 - 2,5
un fil de
Utilis er serrat ed
-rollin g, dente lées
x 3/8" thread e de filets,
s: 8-32 x 3/8" roulag
Lid screw rcle: 8-32
Vis du couve
locatio ns. humid es.
Suitab le for damp ceme nts
aux empla
Convi ent
is remov ed. ur est ouver t.
plastic cover
void if inner rcle plastiq ue intérie
Warra nty si le couve
annul ée
Garan tie s injury or death.
in seriou
. May result ng.
Shock hazard servic ing or installi r de graves teur
WARN ING: power before trocuti on. Peut cause du disjonc
Discon nect r d'élec r l'alime ntation
ENT : Dange ne. Coupe de l'instal lation.
AVERT ISSEM de la person l'entre tien
ou le décès ge ou à
lésion s procéd er au monta
avant de
Need Help? Please visit the Hi-lume
call Lutron Customer Assistance at 1.844.LUTRON1 (1.844.588.7661)
®
Mounting
(mount as shown on the right)
1. Remove top cover to access multi-sided mounting key holes.
2. Mount driver per the options shown to the right.
Notes
• Minimum of 3 in (76 mm) required between any two LED drivers.
Install in accordance with all national and local electrical codes.
•
• Mount driver in a position where it can be easily located and accessed if
service or troubleshooting is necessary.
• Any other mounting configuration will require additional mechanical support.
Improper installation may result in hazards to personnel or property.
Wiring
(wire as shown below)
WARNING: Shock Hazard. May result in serious injury or death.
Turn off power at circuit breaker before installing the unit.
1. Remove top cover to access the terminal blocks.
2. Open necessary knockouts to pass wires into the wiring compartment.
3. Connect the necessary wires according to the illustration below. For E1 / E2
wiring, please refer to Application Note #142. Terminals accept 12 AWG to
20 AWG (0.50 mm 2 to 2.5 mm 2 ).
4. Optional - Add barrier between non-Class 2 and Class 2 wires
(e.g., EcoSystem wiring shown below has E1 / E2 as Class 2, therefore
TM
barrier is placed between input and control terminal block).
5. Rotate Field Adjustment Knob to full counter-clockwise position.
6. Ensure compatible dimmer and load are installed and restore power to the
circuit. See reverse side for Compatible Controls.
3-Wire Controls
To LED Load
+ LED
– LED
3-Wire Wiring Diagram
Switched Hot (L)
+ LED
Dimmed Hot (DH)
Hi-lume
®
Premier
0.1% Neutral (N)
Driver
– LED
Ground* (D)
LED
Light
Ground*
Engine
* Driver and control must be grounded in accordance with local and national electrical codes.
Premier 0.1% page at www.lutron.com or
®
A barrier (included) in the wiring compartment separates non-Class 2
and Class 2 wires. Barrier can be placed between control and output
terminals (Option 1) or between input and control terminals (Option 2).
Option 1
Output
Control
Input
Option 3
Mounting Surface
EcoSystem Controls
TM
From Line/Control
120 – 277 V~
50 / 60 Hz
To LED Load
Switched Hot (L)
+ LED
Dimmed Hot (DH)
– LED
Neutral (N)
Ground* (D)
EcoSystem Wiring Diagram
TM
Hot
Lutron
®
3-Wire
Dimmer
+ LED
Hi-lume
Premier
Ground*
0.1%
– LED
Neutral
Driver
LED Light
Engine
Option 2
Barrier
Barrier
Output
Control
Input
To EcoSystem Digital Link
TM
E1
E2
From Line/Control
120 – 277 V~
50 / 60 Hz
Hot (L)
Neutral (N)
Ground* (D)
E1
To EcoSystem
TM
E2
Digital Link
Hot (L) Hot
®
Neutral (N) Neutral
Ground* (D)
Ground*