Publicidad
Idiomas disponibles
Idiomas disponibles
Hi-lume
Premier 0.1% EcoSystem
®
Compatible Controls
Compatible Controls
• 3-Wire Controls
• EcoSystem
Controls
TM
Consult individual component installation
guides for more details.
Driver Leads
Maximum wire length between LED driver and
start of the light engine:
Wire Gauge*
Maximum Lead Length
2
20 AWG (0.50 mm
) 15 ft (4.5 m)
18 AWG (0.75 mm
2
)
25 ft (7.62 m)
2
16 AWG (1.00 mm
)
40 ft (12.2 m)
14 AWG (1.50 mm
2
)
60 ft (18.3 m)
12 AWG (2.50 mm
2
)
100 ft (30.5 m)
10 AWG (4.00 mm
2
)* 150 ft (45.7 m)
* To use wire gauges larger or smaller than terminal
blocks' rated gauge of 20 AWG to 12 AWG (0.50 mm
2
2
to 2.50 mm
), connect 1 ft (0.31 m) or less of rated wire
from terminal and connect with larger or smaller wire.
Field Adjustment Knob
Adjusting knob on the outside of the enclosure
changes the minimum light level
that is reached during normal
operation. This feature enables the
user to address light output
mismatch between two or more
drivers at low-end dim level. Driver
is initially defaulted to the minimum
light output when at low-end. For
more information, please refer to
Application Note #591 (P/N 048591)
at www.lutron.com
1. Ensure knobs on all drivers are in
the full counter-clockwise position.
2. Set control to get lowest light level.
3. Turn knob clockwise to adjust light output to
match the brightest driver.
4. Repeat steps 2-3 for the remaining drivers.
Warranty
For warranty information, please visit:
www.lutron.com/DriverWarranty
)Lutron, Lutron, Ariadni, Diva, GRAFIK Eye, Hi-lume,
HomeWorks, Maestro, Maestro Wireless, Nova, Nova T*,
PowPak, Quantum, RadioRA, and Skylark are registered
trademarks and Energi Savr Node, Soft-on, Fade-to-
Black, and EcoSystem are trademarks of Lutron
Electronics Co., Inc.
©2015 – 2016 Lutron Electronics Co., Inc.
/ 3-wire Voltage LED Driver
TM
Compatible Controls
For assistance in selecting controls, contact our LED Center of Excellence.
3-Wire Controls
(without Soft-on, Fade-to-BlackT dimming technology)
Model Number
Product
120 V~
277 V~
NTF-10-
NTF-10-277-
Nova T*
®
NTF-103P-
NTF-103P-277-
NF-10-
NF-10-277-
Nova
®
NF-103P-
NF-103P-277-
SF-10P-
SF-12P-277-
Skylark
®
SF-103P-
SF-12P-277-3
DVF-103P-
DVF-103P-277-
Diva
®
DVSCF-103P- DVSCF-103P-277-
Ariadni
AYF-103P-
AYF-103P-277-
®
MAF-6AM-
MAF-6AM-277-
Maestro
®
MSCF-6AM-
MSCF-6AM-277-
r 0 .1 %
Maestro Wireless
o m
MRF2-F6AN-DV-
lu tr o n .c
®
P r e m ie
H i- lu m e
RadioRA
2
TM
RRD-F6AN-DV-
-U
®
6 W 2 4 V
L 3 D 0 -9
er
LE D D riv
to -B la ck
V ol ta ge
TM
, F ad e-
on st an t
S o ft -o n
3- w ire C
HomeWorks
QS
HQRD-F6AN-DV
n o ir
D E L
te m
fo n d u au
nt e po ur
E co S ys
®
TM
n co ns ta
e d o u x,
fil te ns io
A llu m ag
77 .7 66 1)
P ilo te 3-
(1 .8 44 .5
te m
PHPM-3F-120
T R O N 1
—
E co S ys
TM
1. 84 4. LU
an ad a:
Interface
U S A / C
PHPM-3F-DV
M ax
11 0 W
- 0, 40 A
nt ré e:
BCI-0-10
In pu t | E
H z 0, 92
50 / 60
7 V ~
12 0 - 27
GP Dimming Panel
Various
:
| S or tie
C la ss 2
O ut pu t
4 A M ax
EcoSystem
Controls
24 ,0 V
(with Soft-on, Fade-to-BlackT dimming technology)
t K no b
TM
or tie
dj us tm en
se de S
ut pu t A
m ité B as
Li gh t O
ur l'E xt ré
Model Number
Lo w E nd
la ge po
de R ég
Product
B ou to n
iè re
120 – 277 V~
de Lu m
PowPak
Dimming Module
RMJ-ECO32-DV-B,
®
on ly .
en t.
with EcoSystem
G w ire
URMJ-ECO32-DVB
se ul em
- 12 A W
5 m m ²
®
U se 20
0, 50 - 2,
un fil de
PowPak
U til is er
Wireless Fixture
FCJ-ECO
rra te d
llin g, se
ée s
®
s, de nt el
re ad -ro
Control with EcoSystem
x 3/ 8" th
‡
e de fil et
FCJS-ECO
w s: 8- 32
8" ro ul ag
®
8- 32 x 3/
Li d sc re
uv er cl e:
Vi s du co
QSN-1ECO-S, QSN-2ECO-S,
Energi Savr Node
with
ns .
p lo ca tio
TM
m id es .
QSN-2ECO-PS120,
fo r da m
en ts hu
EcoSystem
Su ita bl e
pl ac em
®
t au x em
UQSN-1ECO-S, UQSN-2ECO-S
C on vi en
m ov ed .
es t ou ve
rt.
ve r is re
in té rie ur
as tic co
GRAFIK Eye
QS with
QSGRJ-_E,
in ne r pl
as tiq ue
®
er cl e pl
y vo id if
W ar ra nt
si le co uv
EcoSystem
QSGR-_E
an nu lé e
or de at h.
®
G ar an tie
us in ju ry
lt in se rio
M ay re su
lin g.
Quantum
ha za rd .
or in st al
QP2-_P_C
es
de gr av
: Sh oc k
se rv ici ng
®
ca us er
nc te ur
W AR NI NG
r be fo re
n. Pe ut
du di sjo
tro cu tio
en ta tio n
ct po we
Di sc on ne
er d' él ec
er l'a lim
LQSE-2ECO-D,
tio n.
T : Da ng
ne . Co up
l'in st al la
HomeWorks
QS with
SS EM EN
la pe rs on
tie n de
à l'e nt re
AV ER TI
cè s de
®
ta ge ou
QSGRJ-_E,
ou le dé
au m on
lé sio ns
EcoSystem
pr oc éd er
®
av an t de
QSGR-_E,
NOTE: For information about Legacy product use in existing control application, contact LEDs@lutron.com
** No derating required in multigang applications provided that the driver count does not exceed the quantity listed.
†
21% trim allows for 0.1% low-end level but might result in dead travel for 1% – 4% on user interface. 22% trim can be used to avoid dead travel but
may result in >0.1% low-end level.
‡
All devices connected to one PowPakR wireless fixture controller will be controlled together. Devices will dim to the same level as the result of a
control command. Control will need to have low-end level reprogrammed to dim to 0.1% output. For more details, refer to Application Note #556 at
www.lutron.com.
§
Version 3.1 (or higher) is required to dim lower than 1%.
*
Version 7.0 (or higher) is required to dim lower than 1%.
r
For lower system versions, please visit www.lutron.com/LEDsystemcheck to check if your system requires changes.
Drivers per Control**
Load Selection
Low-end
Type
trim setting
120 V~
277 V~
1 – 16
1 – 19
—
—
1 – 8
1 – 14
—
—
1 – 16
1 – 19
—
—
1 – 8
1 – 14
—
—
1 – 8
1 – 14
—
—
1 – 8
1 – 14
—
—
1 – 8
1 – 14
—
—
1 – 8
1 – 14
—
—
1 – 8
1 – 14
—
—
1 – 6
1 – 14
—
—
1 – 6
1 – 14
—
—
1 – 6
1 – 14
—
—
Dual voltage 3-wire
1 – 6
1 – 14
21%
†
dimmer
Fluorescent 3-wire
1 – 6
1 – 14
21%
†
LED 3-wire
1 – 16
—
—
—
1 – 16
1 – 38
—
—
1 – 16
1 – 38
—
—
1 – 16
1 – 38
2 – 1
—
Drivers per Control
Recommended
System Version
r
120 V~
277 V~
5.9 or higher
32 per EcoSystem
link
®
0796534 or higher 3 per EcoSystem
link
®
9.027 or higher
64 per EcoSystem
link
®
—
9.009 or higher
64 per EcoSystem
link
®
§
—
3.2 or higher
64 per EcoSystem
link
®
—
10 or higher*
64 per EcoSystem
link
®
L3D0-96W24V-U Troubleshooting
Problem
Possible Solution
LED does not illuminate
• Verify that the system is wired correctly according to wiring diagram and
at high-end
powered.
• Verify that the LED load is wired correctly; +LED to positive, -LED to negative.
• Verify that the LED load is for "constant-voltage" applications with PWM
dimming.
• Verify that the LED load is compatible with the specified voltage output
of the driver.
• Lutron
drivers are not for use with MR16 LED lamps.
®
†
LED does not illuminate
• Verify that the low-end trim on the control is set properly.
at low-end
• Turn Field Adjustment Knob clockwise until desired low-end operation is
obtained.
LED does not dim
• Verify that Switched Hot and Dimmed Hot are connected to the proper
terminals for 3-wire control.
• Verify EcoSystem
control wiring (E1 and E2) is wired according to the
TM
instructions for digital control.
LED turns on / off
• Turn Field Adjustment Knob counter-clockwise until desired low-end
abruptly without Soft-on,
operation is obtained.
Fade-to-BlackT feature
• 3-wire control does not have Soft-on, Fade-to-BlackT dimming
technology.
LED is flashing,
• Verify that a compatible dimmer is being used to control the driver.
flickering, dropping out,
• Verify that the input voltage is within the rated limits.
or has poor dimming
• Verify that Switched Hot and Dimmed Hot are connected to the proper
performance
terminals.
• Verify that the LED load is for "constant-voltage" with PWM dimming
applications.
• Verify that the length of wires between driver and LED does not exceed
specification.
• Verify that the rated voltage is present at the driver.
• Certain types of LED loads may be incompatible.* Verify that the LED
load is within the specified wattage range of 25 W to 96 W.
• Lutron
drivers are not for use with MR16 LED lamps.
®
LED is flashing slowly
• Verify that the LED load does not exceed the maximum specified power
(6 to 8 second interval)
rating of the driver (96 W).
• Verify that the LED load matches the specified voltage output of the driver.
• Verify that the length of wire between driver and LED does not exceed
specification.
• Certain types of LED loads may be incompatible.
LED output appears
• Verify that rated line voltage is present at the terminal.
dim at high-end
• Verify that the driver is operating in an environment within its ambient
temperature rating.
• Verify that the driver is not located adjacent to other heat producing
devices. Verify that space between drivers is greater than 3 in (76 mm).
• Verify that the maximum lead length is not exceeded per Lutron
recommendation.
• Verify that the LED load is installed per manufacturer's instructions.
• Verify that the LED load is compatible with the specified voltage output
of the driver.
Not all LED strips/
• Verify that multiple LEDs connected to a single driver are properly wired.
fixtures illuminate
• Verify that the LED load is installed per manufacturer's instructions.
Not all LEDs on the
• Verify that the length of wire between the driver and LED does not
same strip are evenly lit
exceed specifications.
• Verify that the LED load is for "constant-voltage" with PWM dimming
applications.
• Verify that the LED load is installed per manufacturer's instructions.
LED is brighter / hotter
• Verify that the LED load is compatible with the specified voltage output
than expected
of the driver.
* Certain constant-voltage loads may have added capacitance. Contact the Lutron
more information about these loads.
*
®
LED Center of Excellence at 1.877.346.5338 for
®
Publicidad
