Program Change - Yamaha Clavinova Serie Manual De Instrucciones

4. PROGRAM CHANGE

Data format: [CnH] -> [ppH]
CnH = Program event (n = channel number)
ppH = Program change number
Voice Name
GRANDPIANO 1
VARIATION
GRANDPIANO 2
VARIATION
GRANDPIANO 3
VARIATION
E.PIANO 1
VARIATION
E.PIANO 2
VARIATION
HARPSICHORD
VARIATION
VIBRAPHONE
VARIATION
CHURCH ORGAN
VARIATION
JAZZ ORGAN
VARIATION
STRINGS
VARIATION
CHOIR
VARIATION
GUITAR/CLAVI.
VARIATION
WOOD BASS
VARIATION
E.BASS
VARIATION
• If you assign Program Change numbers using numbers 0
through 127, subtract one (1) from a Program change number
(P.C. #) listed above. For example, if you wish to change to a
Program with the P.C. #1, specify number 0.
• When program change reception is turned OFF in the Func-
tion mode, no program change data is transmitted or received.
Also, Bank MSB/LSB is not transmitted or received.
5. SYSTEM REALTIME MESSAGES
[rrH]
F8H: Timing clock
FAH: Start
FCH: Stop
FEH: Active sensing
Data Transmission
Transmitted every
F8H
96 clocks
FAH Recorder start
FCH Recorder stop
Transmitted every
FEH
200 milliseconds
• Caution: If an error occurs during MIDI reception, the Damper,
Sostenuto, and Soft effects for all channels are turned off and
an All Note Off occurs.
70 Appendix
CLP-F01
P.C.#=Program Change number
P.C.#
MSB LSB
(1–128)
0 122 1
0 123 1
0 112 1
0 112 2
0 122 2
0 122 4
0 122 6
0 122 89
0 122 5
0 123 5
0 122 7
0 123 7
0 122 12
0 122 13
0 123 20
0 122 20
0 122 17
0 123 17
0 122 49
0 122 50
0 122 53
0 123 53
0 122 25
0 122 8
0 122 33
0 124 33
0 122 34
0 122 36
Reception
Received as 96-clock tempo timing
when MIDI clock is set to External
Recorder start
Not received when the MIDI clock is
set to Internal.
Recorder stop
Not received when the MIDI clock is
set to Internal.
If a signal is not received via MIDI for
more than 400 milliseconds, the
same processing will take place for All
Sound Off, All Notes Off and Reset All
Controllers as when those signals are
received.
6. SYSTEM EXCLUSIVE MESSAGES
(Yamaha MIDI Format)
Panel Data Transmit
Data format: [F0H] -> [43H] -> [0nH] -> [7CH] -> ... -> [F7H]
F0H, 43H, 0nH, 7CH (n: channel number)
00H, 2DH (data length)
43H, 4CH, 20H, 20H (CL)
43H, 4CH, 50H, 27H, 30H, 34H (CLP'04)
30H, 30H (version x, y)
[PANEL DATA]
[CHECK SUM (1byte)] = 0-(43H+4CH+20H+......+Data end)
F7H
• Panel Data Contents
(1) 1'st Voice
(2) Dual On/Off
(3) Dual Voice
(4) Dual Balance
(5) Dual Detune
(6) Dual Voice1 Octave
(7) Dual Voice2 Octave
(8) Dual Voice1 Effect Depth
(9) Dual Voice2 Effect Depth
(10) Split On/Off
(11) Split Voice
(12) Split Point
(13) Split Balance
(14) Split Voice1 Octave
(15) Split Voice2 Octave
(16) Split Voice1 Effect Depth
(17) Split Voice2 Effect Depth
• Panel data send requests cannot be received.
7. SYSTEM EXCLUSIVE MESSAGES
(Universal System Exclusive)
(1) Universal Realtime Message
Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] ->
[llH] -> [mmH] -> [F7H]
MIDI Master Volume
• Simultaneously changes the volume of all channels.
• When a MIDI master volume message is received, the volume
only has affect on the MIDI receive channel, not the panel
master vol-ume.
F0H = Exclusive status
7FH = Universal Realtime
7FH = ID of target device
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH = Volume LSB
mmH = Volume MSB
F7H = End of Exclusive
or
F0H = Exclusive status
7FH = Universal Realtime
XnH = When n is received n=0~F, whichever is received.
X = don't care
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH = Volume LSB
mmH = Volume MSB
F7H = End of Exclusive
(18) Split Dumper Mode
(19) Reverb Type 1
(20) Reverb Type 2
(21) Reverb Depth 1
(22) Reverb Depth 2
(23) Effect Type 1
(24) Effect Type 2
(25) Effect Depth
(26) Variation On/Off
(27) Touch Sensitivity
(28) Fixed Data
(29) Left Pedal
(30) Soft Pedal Depth
(31) Absolute tempo low byte
(32) Absolute tempo high byte
(33) Key-Off Sampling Depth