HIKVISION DS-PD2-P12QE-C Manual De Instrucciones

DS-PD2-P12QE-C
Wired Ceiling Mounted PIR Detector
This product and - if applicable - the supplied accessories too are marked with "CE" and
comply therefore with the applicable harmonized European standards listed under the
2011/65/EU.
For electrical products sold within the European Community. At the end of the
electrical products life, it should not be disposed of with household waste.
for recycling advice in your country.
EN50131-2-2:2008
EN50131-1:2006+A1:2009
Security Grade (SG) 2
Environmental Class (EC) II
Perform steps one to five. To prevent damage to components,
product. Do not touch the pyro sensor highlighted in step 2.
Install wires away from mains cabling. Fix the product to solid ceilings
that do not vibrate. False alarms may be caused by direct sunlight,
completely obscure the product's field of view.
EOL resistance
Place two-pin jumpers onto header pins to select the End Of Line
Alarm Tamper
Place two-pin jumpers onto header pins to enable the LED and adjust
LED
Remotely enabling the LED
If you disable the product's LED, you can use a control panel to
remotely enable the LED for walk tests. To remotely enable the LED,
connect the product's LED terminal to a control panel at 0V.
Wiring
e
Detectors
Volumetric 6 zone, 3 planes yes
Volumetric Coverage 360° 156 zones 3 planes , ,
Ceiling mount PIR y s
Ceiling Mount PIR Yes
Quad-interlocking element pyroelectric sensor yes
Quad-Interlocking Element Pyroelectric Sensor Yes
Independent Floa ng Threshold (IFT) t ye
Independent Floa ng Threshold (IFT) Technology Yes
~9-16V DC
Adjustable se yes
Adjustable Sensi vity Yes
Automa c t yes
Automa c Yes
Detectors
Maximum r 12m
Maximum Range 12 m
Alarm r 2.5 s conds
Alarm Response 2.5 seconds
Detec on 0.3-3m/s
Detec on Speed 0.3-3m/s
Geometric l 3D
Geometric 3D
Storage temperature
Moun ng
-
Op mal i 40°C to +80°C 2.4-4m
Op mal 2 .4-4m
Electrical
Power supply 9-16VDC (12VDC nominal) 9-16DC (12DC nomi al)
Power Supply
Relay Type Solid state
-10°C to +40°C
Outputs 6 DC, 50mA a
Outp uts Relay 60VDC , 50mA max
Temperature -10 °C to 40 °
!
The Input voltage should meet both the SELV (Safety Extra Low Voltage) and
the Limited Power Source according to the IEC60950-1 standard. Please refer
to technical speci cations for detailed information.
1 2
6K8
5K6
4K7
2K2
1K
LED LED
AUTO
Hangzhou Hikvision Digital Technology CO.,Ltd. No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
24mm
33mm
94mm
62g
3 4
N/C Wiring
5K6
4K7
2K2
1K
6K8
5K6
4K7
2K2
1K
DEOL Wiring
the example values 2k2 for
alarm, 2k2 for tamper(EOL).
LOW
HIGH
2.4m
3.0m
10m
11m
12m
5
CONTROL PANEL
A T
+12V OV A T
EOL COM
-
+
ALARM TAMPER LED
5K6
4K7
2K2
1K
Detector
CONTROL PANEL
+12V OV Z1 COM Z2 Z3
-
+
ALARM TAMPER LED
6K8 5K6
5K6 4K7
4K7 2K2
2K2 1K
1K Detector
GENERIC CONTROL PANEL
+12V OV Z1 COM Z2 Z3
-
+
ALARM TAMPER LED
6K8 5K6
5K6 4K7
4K7 2K2
2K2 1K
Detector
1K
4.0m