HIKVISION DS-PD2-T10AME-EH Manual De Instrucciones

DS-PD2-T10AME-EH/EH1
EN50131-2-4:2008
EN50131-1:2006+A1:2009
Security Grade (SG) 2
Environmental Class (EC) IV
This product and - if applicable - the supplied accessories too are marked with
"CE" and comply therefore with the applicable harmonized European standards
For electrical products sold within the European Community. At the end of the
electrical products life, it should not be disposed of with household waste. Please
recycling advice in your country.
Diagram References
technology to detect when one or both PIR detectors as well as the
Microwave module are Masked.
view of the PIR or MW sensors.
The masking area is adjustable between 0 to 1M.
If the masking area is entered the Blue LED starts flashing to show that
detector, the obstacle must be removed and a walk test should be done.
terminal has to be connected to an output of the panel which is POSITIVE
when ARMED. To enable this feature also, switches 2 and 4 must be OFF.
Blocking:
or less and is used when the panel is disarmed. When the blocking feature is
To enable the feature, switches 3 and 4 must be OFF and the RI input
should be connected to an output on the control panel which gives a
NEGATIVE when DISARMED and a POSITIVE when ARMED.
Detectors Detectors
Automa c Yes Maximum Range 10 m
Digital Yes Volumetric Coverage Yes
DEOL Resistor on Board Yes
Curtain Coverage Op onal
Tamper Front, and rear
Animal Immunity 10 k g
Intergrated Walk Test Buzzer Yes
Tri Technology 2 infrared and 1 microwave
Separate LED Indica on Yes
Detec on Speed 0.25 - 2.5m/s
3 Microwave Frequencies to Avoid Yes
Coverage Angle 90 degree
Digital Independent Yes
Detec on Zones 78
An - Yes
Detec on Planes 5
Adjustable Auto or high
Adjustable g ( ) Yes
Electrical
Protec on Ultraviolet light filter
Opera ng Voltage 9-16VDC, 13.8VDC typically
Lens 2 × Lens 5 volumetric lens (UV Compensated)
Quiescent 67mA @ 13.8VDC
Op cs Sealed op cs
Relay Outputs 3 x SELV limits, 60VDC 50mA (42.4VAC peak)
Detec on Method 2 low noise dual element passive infrared
Tamper Switch 12VDC 50mA both front and rear
An Blocking Technology Yes
Environmental and
Moun ng
-25 °C to +60 °C
Wall Mounted Yes - addi onal wall and fixed brackets
Physica Dimensions (H × W × D) 188 × 84 × 77 mm
Op mum Coverage Height 1.8-2.4m
Weight 300 g
Adjustable Lens Masks
FIXEDBRACKET + Fixed Lens Mask
WALLBRACKET + XD-45D-ADAPTER
Warning
For electrical products sold within the European Community. At the end of
the electrical products life, it should not be disposed of with household
or retailer for recycling advice in your country.
COPYRIGHT ©2018 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
About this Manual
This manual is applicable to detector.
other reasons. Please find the latest version in the company website
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
UD15567B
START
3EOL
3k
15k
12k
8k2
6k8
5k6
EOL EOL EOL R1 LED ALARM N/O EOL
4k7
TAMPER ALARM N/C MASK/FAULT TAMPER ALARM N/C MASK/FAULT
2k2
1k
10k
10k
5k6
6k8
4k7
5k6
3k9
4k7
2k7
3k9
2k2
2k7
1k5
2k2
A A T T 1k
+12V 0V 1k5 +12V 0V
EOL INPUT 1 COM
1k
820R
1M
MAX
Max: 1M
30% Mask
≤1m
Hangzhou Hikvision Digital Technology CO.,Ltd.
WALLBRACKET
FIXEDBRACKET
MASK/ALARM LINK
DEOL
N/C
3k
15k
12k
8k2
6k8
5k6
EOL EOL R1 LED ALARM N/O EOL EOL EOL R1 LED
4k7
TAMPER ALARM N/C MASK/FAULT
2k2
1k
10k
10k
5k6
6k8
4k7
5k6
3k9
4k7
2k7
3k9
2k2
2k7
1k5
2k2
A A T T 1k A A T T
1k5 +12V 0V
EOL INPUT 1 COM EOL INPUT 1 COM
1k
820R
30%
OFF
>1m
No.555 Qianmo Road, Binjiang District, Hangzhou 310052, China
!
The Input voltage should meet both the SELV (Safety Extra Low Voltage) and
the Limi ted Power Source according to the IEC60950-1 standa rd. Please refer
to t ations for detailed information.
OFF
GENERAL WIRING
HIK
3k
15k
3k
12k
15k
8k2
12k
6k8
8k2
5k6
6k8
ALARM N/O
4k7 5k6
EOL EOL EOL R1 LED ALARM N/O
2k2 4k7
TAMPER ALARM N/C MASK/FAULT
2k2
1k
1k
10k
10k
10k 10k
5k6
6k8
5k6
6k8
4k7
5k6
5k6 4k7
3k9
4k7 3k9
4k7
2k7
3k9 3k9 2k7
2k2 2k7 2k2
2k7
1k5
1k5 2k2
2k2
+12V 0V Z1 COM Z2 Z3 1k5 1k
1k
1k5
1k
HIK CONTROL PANEL
1k
820R
820R
EOL EOL EOL R1 LED ALARM N/O
TAMPER ALARM N/C MASK/FAULT
+12V 0V
PCX 46
PCX
ATE INPUTS
GENERAL
3k
15k
12k
8k2
6k8
5k6
EOL EOL EOL R1 LED ALARM N/O
4k7
TAMPER ALARM N/C MASK/FAULT
2k2
1k
10k 10k
5k6
6k8
5k6 4k7
3k9
4k7
3k9 2k7
2k2
2k7
2k2 1k5
Z1 COM Z2 Z3 1k
+12V 0V 1k5
1k
GENERIC CONTROL PANEL
820R
3k
15k
12k
8k2
6k8
5k6
4k7
2k2
1k
10k
10k
5k6
6k8
4k7
5k6
4k7 3k9
3k9 2k7
2k2
2k7
1k5
2k2
1k
1k5
1k
820R
No resistors are required for
the Alarm N/O relay