Operation And Maintenance; Technical Parameters; Environment Protection - VERTO 50G519 Manual Del Usuario

Switching on:
• Press the switch button (6) and hold in this position.
• Press the switch lock button (3) (fig. A).
• Release pressure on the switch (6).
Switching off:
Press and release the switch (6).
Range of rotational speed of the spindle is controlled with pressure
on the switch button.
WHEEL FOR SPINDLE ROTATIONAL SPEED CONTROL
The drill allows for operation with different spindle speeds. It can be
controlled with the wheel (5) (fig. A). For each setting of the wheel for
speed control, the speed can be adjusted continuously by increasing or
decreasing pressure on the switch button (6).
• Increase the speed by turning the wheel (5) clockwise.
• Reduce the speed by turning the wheel (5) counter-clockwise.
* Refer to graphic symbols on the wheel for rotational speed control or the switch.
Choose proper rotational speed when the drill operates with no load, with
pressed switch lock button. Defined speed may decrease under load.
LEFT – RIGHT DIRECTION OF ROTATION
Choose direction of spindle rotation with the selector switch (4) (fig. A).
Clockwise rotation – set the switch (4) to the extreme left position.
Counter clockwise rotation – set the switch (4) to the extreme right position.
* In certain cases position of the direction selector switch relating to rotation direction may
be different than specified. Please refer to graphic signs placed on the switch or tool body.
Do not change direction of rotation when the spindle of the drill is
rotating. Check if the position of the selector switch is correct before
starting the tool.
OPERATION MODE SWITCH
Operation mode switch (2) allows for choosing suitable work mode:
drilling with or without impact (fig. B). Set the operation mode switch in
the position for drilling without impact (drill symbol), when processing
materials like metal, wood, ceramics, plastics and alike. Set the operation
mode switch in the position for drilling with impact (hammer symbol),
when processing materials like stone, concrete, brick and alike. Holes in
wood, wood-like materials and metals are made with drills of high speed
steel or carbon steel (the latter for wood and wood-like materials only). For
stroke drilling special drills with sintered carbide inserts should be used.
You should not use counter clockwise rotation when impact
function is on.
Long lasting drilling at low rotational speed of the spindle may cause
motor overheating. Provide regular breaks during operation or let the
tool operate at maximum speed with no load for approximately 1–2
minutes. Do not cover holes for motor ventilation in the tool body.

OPERATION AND MAINTENANCE

Unplug the power cord from the mains socket before commencing
any activities related to installation, adjustment, repair or
maintenance.
MAINTENANCE AND STORAGE
• Cleaning the device after each use is recommended.
• Do not use water or any other liquid for cleaning.
• Clean the tool with a dry cloth or blow through with compressed air
at low pressure.
• Do not use any cleaning agents or solvents, they may damage plastic
parts.
• Clean ventilation holes in the motor casing regularly to prevent device
overheating.
• In case of power cord damage replace it with a cord with the same
specification. Entrust the repair to a qualified specialist or return the
tool to a service point.
• In case of excessive commutator sparking, have the technical condition
of carbon brushes of the motor checked by a qualified person.
• Always store the tool in a dry place, beyond reach of children.
DRILL CHUCK REPLACEMENT
• Open chuck (1) jaws.
• Unscrew the chuck fixing screw with cross screwdriver, by turning it
clockwise (left-hand thread).
• Install hex key in the chuck (fig. D).
• Gently tap free end of the hex key.
• Unscrew the chuck.
Installation of the chuck is similar to deinstallation, only the sequence
of actions is reversed.
REPLACEMENT OF CARBON BRUSHES
Replace immediately used up (shorter than 5 mm), burnt or cracked
motor carbon brushes. Always replace both brushes at a time.
Entrust replacement of carbon brushes only to a qualified person.
Only original parts should be used.
All faults should be repaired by service workshop authorized by the
manufacturer.

TECHNICAL PARAMETERS

RATED PARAMETERS
Parameter
Supply voltage
Power supply frequency
Rated power
Range of spindle rotational speed without load
No load impact rate
Drill chuck range
Thread size of the drill chuck
steel
Maximum drilling
concrete
diameter
wood
Protection class
Weight
Year of production
NOISE LEVEL AND VIBRATION PARAMETERS
Noise and vibration information.
Parameters of produced noise level, such as sound pressure level Lp
sound power level Lw
A
below in this manual, in accordance with EN 60745.
Vibration values a and measurement uncertainty K are determined in
h
accordance with EN 60745-2-1 and specified below.
Vibration level specified below in this manual was measured in
accordance with measurement procedure defined in EN 60745-2-1
and can be used to compare power tools. It can also be used for initial
assessment of exposure to vibrations.
Specified vibration level is representative for main applications of the
power tool. Vibration level may change if the power tool is used for
other purposes, with different working tools or will not be maintained
properly. The abovementioned factors may lead to higher exposure to
vibrations during whole working time.
To precisely define exposure to vibrations, include periods when the
power tool is switched off and when it is switched on but not used for
working. This way total exposure to vibrations may be significantly lower.
Use additional safety measures to protect the user against results of
vibration exposure, such as: power tool and working tool maintenance,
proper hand temperature conditions, good work organisation.
Sound pressure: Lp = 86 dB(A) K = 3 dB(A)
A
Sound power: Lw = 97 dB(A) K = 3 dB(A)
A
Vibration acceleration, impact drilling in concrete: a
Vibration acceleration, drilling in metal: a

ENVIRONMENT PROTECTION

Do not dispose of electrically powered products with household
wastes, they should be utilized in proper plants. Obtain information
on wastes utilization from your seller or local authorities. Used up
electric and electronic equipment contains substances active in
natural environment. Unrecycled equipment constitutes a potential
risk for environment and human health.
* Right to introduce changes is reserved.
"Grupa Topex Spółka z ograniczoną odpowiedzialnością" Spółka komandytowa with
seat in Warsaw at ul. Pograniczna 2/4 (hereinafter Grupa Topex) informs, that all
copyrights to this instruction (hereinafter Instruction), including, but not limited to, text,
photographies, schemes, drawings and layout of the instruction, belong to Grupa Topex
exclusively and are protected by laws accordingly to Copyright and Related Rights Act of
4 February 2004 (ustawa o prawie autorskim i prawach pokrewnych, Dz. U. 2006 No 90
item 631 with later ammendments). Copying, processing, publishing, modifications for
commercial purposes of the entire Instruction or its parts without written permission of
Grupa Topex are strictly forbidden and may cause civil and legal liability.
10
Impact drill
0 – 3000 rpm
0 – 48000/min
1,5 - 13 mm
½ '' - 20 UNF
with measurement uncertainty K are specified
= 7,74 m/s
h,ID
= 2,26 m/s K=1,5 m/s
2
h,D
Value
230 V AC
50 Hz
600 W
10 mm
14 mm
23 mm
II
1,6 kg
2020
and
A
K=1,5 m/s
2 2
2