Caracteristiques Techniques - Skil 1116 Manual Original

• On/off switch 9
- switch on/off the tool by pushing knob A in "I"/"O"
position
! before the accessory reaches the workpiece, the
tool should run at full speed
! before switching off the tool, you should lift it
from the workpiece
• Speed control 0
For optimal results on different materials
- select speed with wheel F (also while tool is running)
- use table # as reference for determining the right
speed
- before starting a job, find the optimal speed by testing
out on spare material
! after longer periods of working at low speed,
allow the tool to cool down by running it for
approximately 3 minutes at high speed with no
load
• Holding and guiding the tool !
- pencil grip for precision work (engraving)
- one-hand grip for less precise work (grinding)
- do not apply too much pressure on the tool; let the
speed do the work for you
• Assembly of specific accessories @
MaintEnanCE / SErViCE
• This tool is not intended for professional use
• Always keep tool and cord clean (especially ventilation
slots G 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skil.com)
EnVironMEnt
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
noiSE/ViBration
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 74 dB(A) and the sound
power level 85 dB(A) (standard deviation: 3 dB), and the
vibration 4.2 m/s² (triax vector sum; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
outil rotatif
introDUCtion
• Cet outil est conçu pour le meulage, ponçage,
tronçonnage, gravure, polissage et perçage de haute
précision des différents matériaux
• Cet outil n'est conçu pour un usage professionnel
• SKIL ne fournit pas d'accessoires de rechange pour cet
outil, mais recommande l'achat d'accessoires Ø 2,4 mm/
Ø 3,2 mm DREMEL
• Lisez et conservez ce manuel d'instruction 3

CaraCtEriStiQUES tECHniQUES 1

ElEMEntS DE l'oUtil 2
a Interrupteur marche/arrêt
B Bouton de blocage de l'arbre
C Pince
D Chapeau
E Clé
F Molette pour régler la vitesse
G Fentes de ventilation
H Crochet de suspension
SECUritE
aVErtiSSEMEntS DE SECUritE GEnEraUX PoUr
l'oUtil ElECtriQUE
aVErtiSSEMEnt lisez tous les avertissements de
sécurité, les instructions, les illustrations et les
spécifications fournis avec cet outil électrique. Ne pas
suivre les instructions énumérées ci-dessous peut
provoquer un choc électrique, un incendie et/ou une
blessure sérieuse.
Conservez tous les avertissements et toutes les
instructions pour pouvoir s'y reporter ultérieurement.
Le terme "outil électrique" dans les avertissements se
rapporte à des outils électriques raccordés au secteur (avec
câble de raccordement) et à des outils électriques à batterie
(sans câble de raccordement).
11
1116