Specifications Techniques - Skil 2521 Manual Del Usuario

APPLICATION ADVICE
• Use the appropriate bits *
! only use sharp bits
• When drilling ferrous metals
- pre-drill a smaller hole, when a large hole is required
- lubricate drill bit occasionally with oil
• When turning in a screw at/near the cross cut end or an
edge of wood, pre-drill a hole in order to avoid cracking of
the wood
• For an optimal use of the tool a steady pressure on the
screw is required, especially while removing
• When screwdriving in hard wood one should pre-drill a
hole
• Splinterfree drilling in wood (
• Dustfree drilling in walls )
• Dustfree drilling in ceilings ¡
• Drilling in tiles without skidding ™
• For more tips see www.skileurope.com
MAINTENANCE / SERVICE
• Keep tool and charger clean
- clean charging contacts in charger with alcohol or
contact cleaner
! unplug charger from power source before
cleaning
• If the tool/charger should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool or charger undismantled together with
proof of purchase to your dealer or the nearest SKIL
service station (addresses as well as the service
diagram of the tool are listed on www.skileurope.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 8 will remind you of this when the need for
disposing occurs
• The battery must be kept separate from the natural
environment and should not be disposed of as normal
domestic waste (symbol 9 will remind you of this when
the need for disposing occurs)
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this product
is in conformity with the following standards or
standardized documents: EN 60335, EN 60745,
EN 55014, in accordance with the provisions of the
directives 2006/95/EC, 2004/108/EC, 2006/42/EC
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
Arno van der Kloot
Vice President
Operations & Engineering
SKIL Europe BV, 4825 BD Breda, NL
17.05.2011
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 70 dB(A) (standard deviation:
3 dB) and the vibration ✱ m/s² (hand-arm method;
uncertainty K = 1.5 m/s²)
✱ when drilling in metal <2.5 m/s²
✱ when screwdriving <2.5 m/s²
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintainted accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
Perceuse/visseuse sans fil
INTRODUCTION
• Cet outil est conçu pour le perçage dans le bois, le métal,
la céramique et les matières plastiques; les outils avec
réglage électronique de la vitesse et rotation à droite/à
gauche sont également appropiés pour le vissage et le
filetage
• Lisez et conservez ce manuel d'instruction 3

SPECIFICATIONS TECHNIQUES 1

Couple max. vissage dur suivant ISO 5393: 38 Nm
ELEMENTS DE L'OUTIL 2
A Interrupteur de marche/arrêt et réglage de vitesse
B Voyant du chargeur vert
C Anneau pour réglage du couple
D Position de verrouillage (anneau)
E Commutateur pour inverser le sens de rotation
F Commutateur de vitesse
G Indicateur de niveau de charge de la batterie
H Lampe
10
Jan Trommelen
Approval Manager
2521