Side View; Top View - Lutron GRX-IRPS-WH Instrucciones Para La Instalación

System Diagram
Ceiling
Room A
GRX-IRPS
transmitter
(TX)
Partition
GRX/OMX-AV
GRX-A V
R
INTERF AC E CONT RO L
R
COOPERSB URG, PA 18036 SELV(CLASS 2:USA)
DI P SWITCH SETTINGS (1-4) 0 = ON; 1 = OF F
1 2 3 4 1 2 3 4 1 2 3 4
ADDRESS 1 2 3 4 ADDRESS ADDRES S ADDRESS
0 0 0 0 1 0 1 0 0 5 1 0 0 0 9 1 1 0 0 13
0 0 0 1 2 0 1 0 1 6 1 0 0 1 10 1 1 0 1 14
0 0 1 0 3 0 1 1 0 7 1 0 1 0 11 1 1 1 0 15
0 0 1 1 4 0 1 1 1 8 1 0 1 1 12 1 1 1 1 16
DI P SWITCH SETTINGS (5-8 )
TYPE CONFIGUR AT IO N DI P SETTING
W l l a a t s o i t s n 4S CONT RO L SCENES 1-4, MAIN TA IN OUTPUTS 5 ON 6 ON
SCENES 5-8, MAIN TA IN OUTPUTS 5 OF F 6 ON
7 ON 8 ON SCENES 9-12, MAIN TA IN OUTPUTS 5 ON 6 OF F
SCENES 13-16, MAIN TA IN OUTPUT S 5 OF F 6 OF F
4S CONT RO L SCENES 1-4, MOMENT AR Y OUTPUT S 5 ON 6 ON
SCENES 5-8, MOMENT AR Y OUTPUT S 5 OF F 6 ON
7 ON 8 OF F SCENES 9-12, MOMENT AR Y OUTPUT S 5 ON 6 OF F
SCENES 13-16, MOMENT AR Y OUTPUTS 5 OF F 6 OF F
4Q CONT RO L SEQUENCE 1-4, MAIN TA IN INPUTS 5 OF F 6 ON
SEQUENCE 1-4, MOMENT A RY INPUTS 5 ON 6 ON
7 OFF 8 OFF SEQUENCE 5-16, MAIN TA IN INPUTS 6 OF F 6 OF F
SEQUENCE 5-16, MOMENT A RY INPUTS 6 ON 6 OF F
4PS CONT RO L PAR TITION ST AT US , MOMENT A RY INPUTS 5 ON 6 ON
7 OFF 8 ON PA RT ITION ST AT US , MAIN TA INED INPUTS 5 OF F 6 ON
SPECIAL OCCU PA NC Y SENSOR - SCENE 1 & OF F 5 ON 6 OF F
CONT RO L O CCU PA NC Y SENSOR - OFF ONL Y 5 OF F 6 OF F
7 OFF 8 ON
ADDRESS
CONFIG .
ON
TYPE
SELV (CLASS 2:USA) OF F
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 C 1 2 3 4 5 1 2 3 4 5 C
MUX LINK INPUTS OUTPUTS
LUTR ON
1 2 3 4 C 1 2 3 4 5 1 2 3 4 5 C
MUX LINK INPUTS OUTPUTS
PELV (Class 2: USA) control link
2
R
Room B
GRX-IRPS
receiver
(RX)
W l l a a t s o i t s n
LUTR ON
GRX-IRPS-WH Infrared Transmitter/Receiver Pair
Dimensions and Mounting
• Mount receiver and transmitter in
standard U.S. single-gang
(3.5 in./89 mm deep) wallboxes.
Recess wallbox facedown in
ceiling.
• Mount wallboxes exactly in line
with each other to ensure correct
operation.
• Mount sensors so that the
GRX-IRPS
partition, when closed, separates transmitter
(TX)
the receiver and transmitter.
• Mount the receiver and
transmitter a maximum of 8 ft.
(2.4 m) apart.
• Use adjustable mounting
brackets to align infrared signal
during installation.
• Ensure that the partition will
break the beam when closed.
Some wallboxes may need to be
extended.
GRX-IRPS-WH Infrared Transmitter/Receiver Pair

SIDE VIEW

Standard U.S. single-gang wallboxes (2)
Mount facedown, flush with ceiling surface
1.5 in.
(38 mm)
Partition
GRX-IRPS
receiver
(RX)
8 ft. (2.4 m) maximum
Wallbox

TOP VIEW

Align wallboxes on centerlines
R
3