Indoor Unit; Remote Controller; Outdoor Unit; Preparation Before Operation - Mitsubishi Electric MSZ-FH06NA Manual De Instrucciones

Ocultar thumbs Ver también para MSZ-FH06NA:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

● OPERATING INSTRUCTIONS ●
N
AME OF EACH PART

Indoor unit

Front panel
Air fi lter
(Nano platinum
fi lter)
Air cleaning fi lter
(Electrostatic
Horizontal
anti-allergy
vane
enzyme fi lter and
deodorizing fi lter)
Air outlet
Operation indicator lamp

Outdoor unit

Outdoor units may be different in appearance.
P
REPARATION BEFORE OPERATION
Before operation: Insert the power supply plug into the power outlet and/or turn the breaker on.
Installing the remote controller batteries
4.
Press RESET.
1.
Remove the front lid.
• Make sure the polarity of the batteries is correct.
• Do not use manganese batteries and leaking batteries. The remote controller
could malfunction.
• Do not use rechargeable batteries.
• The battery replacement indicator lights up when the battery is running low. In
about 7 days after the indicator starts lights up, the remote controller stops working.
• Replace all batteries with new ones of the same type.
• Batteries can be used for approximately 1 year. However, batteries with
expired shelf lives last shorter.
• Press RESET gently using a thin instrument.
If the RESET button is not pressed, the remote controller may not operate
correctly.
En-3
Air inlet
Emergency
operation
switch
Page 6
i-see sensor
Page 5
Remote control receiving
section
Air inlet (back and side)
Refrigerant piping
Drainage hose
Air outlet
Drain outlet
2.
Insert the negative
pole of AAA
alkaline batteries fi rst.
3.
Install the front lid.

Remote controller

Battery replacement indicator
Operation
display section
Temperature
buttons
Pages 4, 6, 8
Operation
select button
Page 6
ECONO COOL
button
Page 8
POWERFUL
button
Page 9
SMART SET
button
Page 8
NATURAL
FLOW button
Page 9
SENSOR
(i-see) button
Page 5
CLOCK button
Page 3
Remote controller holder
• Install the remote con-
troller holder in a place
where the signal can be
received by the indoor
unit.
• When the remote con-
troller is not used, place
it in this holder.
Setting current time
1.
Press CLOCK.
4.
Press CLOCK again.
• Press CLOCK gently using a thin instrument.
Signal transmitting
Page 3
section
Distance of signal :
About 20 ft. (6 m)
Beep(s) is (are) heard from
the indoor unit when the
signal is received.
OFF/ON
(stop/operate) button
FAN speed control
button
Page 7
WIDE VANE
button
Page 7
VANE control
button
Page 7
INDIRECT/DIRECT
button
Page 5
TIME, TIMER set buttons
Pages 3, 9
Increase time
Decrease time
WEEKLY TIMER
set buttons
Page 10
RESET button
Pages 3, 4
Lid
Slide the lid down
to open the remote
controller. Slide it down
further to get to the
weekly timer buttons.
Only use the remote controller provid-
ed with the unit.
Do not use other remote controllers.
If two or more indoor units are installed
in proximity to one another, an indoor
unit that is not intended to be operated
may respond to the remote controller.
3.
Press the DAY button
to set the day.
2.
Press either the TIME button
or the TIMER buttons to set
the time.
Each press increases/decreas-
es the time by 1 minute (10
minutes when pressed longer).

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Msz-fh09naMsz-fh12naMsz-fh15naMsz-fh18naMsz-fh18na2

Tabla de contenido