Safety Instructions - Milwaukee AG 11-115 Manual Del Usuario

TECHNICAL DATA
Rated input ....................................................................................................1100 W ....................1100 W ......................... 1100 W
Max. no-load speed ................................................................................... 10 000 min
Grinding disk diameter .....................................................................................115 mm .................. 125 mm.........................125 mm
Thread of work spindle .................................................................................. M 14 ....................... M 14 .............................M 14
Weight without cable ........................................................................................ 2,4 kg ..................... 2,4 kg ...........................2,4 kg
Noise/Vibration Information
Measured values determined according to EN 60 745.Typically, the
A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ............................................................... 90,5 dB(A) ...............90,5 dB(A) ....................90,5 dB(A)
Sound power level (K = 3 dB(A)) ................................................................. 101,5 dB(A) .............101,5 dB(A) ..................101,5 dB(A)
Wear ear protection!
Total vibration values (vector sum in the three axes) determined
according to EN 60 745:
Surface grinding: vibration emission value a
Uncertainty K = ................................................................................................ 1,5 m/s
Disk sanding vibration emission value a
Uncertainty K = ................................................................................................ 1,5 m/s
For other applications, e.g. Abrasive Cutting-Off Operations or Wire
Brushing other vibration values could occure.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in
EN 60 745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications,
with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING!
Read all safety warnings and all instructions, including those
given in the accompanying brochure. Failure to follow the
warnings and instructions may result in electric shock, fire and/or
serious injury. Save all warnings and instructions for future
reference.

SAFETY INSTRUCTIONS

Safety Warnings Common for Grinding, Sanding, Wire
Brushing or Abrasive Cutting-Off Operations:
a) This power tool is intended to function as a grinder,
sander, wire brush, or cut-off tool. Read all safety warnings,
instructions, illustrations and specifications provided with
this power tool. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
b) Operations such as polishing are not recommended to be
performed with this power tool. Operations for which the power
tool was not designed may create a hazard and cause personal
injury.
c) Do not use accessories which are not specifically designed
and recommended by the tool manufacturer. Just because the
accessory can be attached to your power tool, it does not assure
safe operation.
d) The rated speed of the accessory must be at least equal
to the maximum speed marked on the power tool. Accessories
running faster than their rated speed can break and fly apart.
e) The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled.
.................................................. 6,3 m/s
h
......................................................... 5,0 m/s
h
f) The arbour size of wheels, flanges, backing pads or any
other accessory must properly fit the spindle of the power
tool. Accessories with arbour holes that do not match the
mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect
the accessory such as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory
and run the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break apart during
this test time.
h) Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and shop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of
stopping flying debris generated by various operations. The dust
mask or respirator must be capable of filtrating particles generated
by your operation. Prolonged exposure to high intensity noise may
cause hearing loss.
i) Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal protective
equipment. Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate area of
operation.
AG 11-115 AG 11-125
............. 10 000 min
-1
................... 6,3 m/s
2
................... 1,5 m/s
2
................... 5,0 m/s
2
................... 1,5 m/s
2
AG 11-125 X
..................10 000 min
-1 -1
.........................6,3 m/s
2 2
.........................1,5 m/s
2 2
.........................5,0 m/s
2 2
.........................1,5 m/s
2 2
English
11
GB