Expression Pedal - Fender MUSTANG I Manual Del Proprietário

• Mode 3—In Mode 3 the footswitch is used to bypass the
Stompbox, Modulation or Delay effects, using the buttons
labeled: STOMP / MOD / DELAY (in line with the MODE 3
LED). The footswitch button LEDs indicate the effects that are
active, just like the buttons on the amplifier.
♫
You can also have a footswitch button assigned to
bypass the Reverb effect by adding on the 2-button
Mustang footswitch (see Six-Button Footswitching
options, below).
• Tuner Mode—Press and hold the MODE button to activate
the Tuner. The ampifier screen and the footswitch both will
display the same tuner information so that you can look in
either place to tune your guitar. The footswitch will display
the nearest note; the button LEDs will indicate sharp and
flat and "in tune" is indicated when the green LED below the
footswitch display lights up.
Press any footswitch button to exit Tuner mode.
Two-Button Footswitch (0080997000)
Connect a 2-button footswitch to your Mustang amplifier
(included with the Mustang III, optional equipment for the
Mustang IV & V) to enable remote multi-function foot control.
Use the Utility menus (see page 12) to assign one of the fol-
lowing functions to the 2-button footswitch:
• Select presets (up/down)
• Select Quick Access presets (QA1/QA2)
• Bypass effects (various combinations)
• Set TAP interval
Six-Button Footswitching options
Plug both a 4-button and a 2-button footswitch into your
Mustang amplifier to expand your remote control options.
By assigning different functions to each footswitch you can
create more than a dozen different foot control combinations.
For example, you could assign Quick Access presets to the
4-button footswitch and Up/Down presets to the 2-button
footswitch. Or you could bypass effects with the 4-button
footswitch and select presets with the 2-button footswitch.
The choice is up to you.
10
MUSTANG I I I /I V/V ( V. 2)
™
f e n d e r . c o m
EXP-1 Expression Pedal
The EXP-1 expression pedal (P/N 2301050000) is a dual-mode
pedal that can be programmed to control a wide variety of
parameters on your Mustang amplifier. Plug the EXP-1 pedal
into the "4 BUTTON FOOTSWITCH" jack .
The EXP-1 operates in two modes, Volume behavior mode
and Expression behavior mode. Switch between modes by
pressing down hard on the toe end of the pedal. Red and
green LEDs on the EXP-1 indicate the current pedal mode:
• Volume
behavior mode (green) is used to control master
volume (or the EXP-1 can be set to OFF in Volume mode).
• Expression
behavior mode (red) can be used to control
most effect and amp parameters on your Mustang amplifier.
Some common uses are to control the frequency parameter
of a wah effect or the rate/time parameter of a modulation
or delay effect.
♫
Fender® FUSE™ software can also be used to program
all settings on your EXP-1 pedal.
EXP-1 Pedal Calibration
The first time you connect the EXP-1 to your Mustang ampli-
fier, you should calibrate it so that the desired range of pedal
movement registers with the amplifier. Calibration takes less
than a minute:
To calibrate the EXP-1:
1.
Plug the EXP-1 pedal into the 4 BUTTON FOOTSWITCH
jack on the back of your Mustang amplifier using the
included cable.
2.
Turn the amplifier OFF.
3.
Press and hold the UTIL button on the amplifier, then
turn the amplifier ON. Continue holding the UTIL button
down until it is no longer illuminated.
4.
Move the EXP-1 pedal between the desired heel and toe
endpoints to set the range of pedal movement that is
registered (recognized) by the amplifier.