Additional Safety Rules For Charger & Battery Cartridge - Makita 4334D Manual De Instrucciones

ENGLISH
1 Button
2 Battery cartridge
3 Charging light
4 Lever
5 Lock-off button
6 Switch trigger
7 Speed adjusting dial
8 Base
9 Anti-splintering device
10 Screw
11 Plastic base plate
12 Hex wrench
SPECIFICATIONS
Model
Length of stroke ............................................. 26 mm
Max. cutting capacities
Wood ......................................................... 135 mm
Mild steel ..................................................... 10 mm
Aluminum .................................................... 20 mm
Strokes per minute ................................ 500 – 2,800
Overall length ............................................... 281 mm
Net weight ....................................................... 3.3 kg
Rated voltage ............................................ D.C. 18 V
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
IMPORTANT SAFETY INSTRUCTIONS
FOR CHARGER & BATTERY
CARTRIDGE
1. SAVE THESE INSTRUCTIONS — This manual
contains important safety and operating
instructions for battery charger.
2. Before using battery charger, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using
battery.
3. CAUTION — To reduce risk of injury, charge
only MAKITA type rechargeable batteries.
Other types of batteries may burst causing
personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or
sold by the battery charger manufacturer may
result in a risk of fire, electric shock, or injury
to persons.
6. To reduce risk of damage to electric plug and
cord, pull by plug rather than cord when dis-
connecting charger.
7. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise sub-
jected to damage or stress.
Explanation of general view
13 Bolt
14 Guide rule
15 Threaded knob
16 Circular guide
17 Pin
18 Vacuum head
19 Blade installing lever
20 Blade holder
21 Clamp
22 Roller
23 Slot
8. Do not operate charger with damaged cord or
4334D
9. Do not operate charger if it has received a
10. Do not disassemble charger or battery car-
11. To reduce risk of electric shock, unplug
12. The battery charger is not intended for use by
13. Young children should be supervised to
14. If operating time has become excessively
ENC001-3
15. If electrolyte gets into your eyes, rinse them
ADDITIONAL SAFETY RULES FOR
CHARGER & BATTERY CARTRIDGE
1. Do not charge battery cartridge when tempera-
2. Do not attempt to use a step-up transformer,
3. Do not allow anything to cover or clog the
4. Always cover the battery terminals with the
24 Blade
25 Hold blade against blade
holder
26 Cutting line
27 Base securing lever
28 Dent mark
29 Slot
30 Graduations
31 Limit mark
32 Screwdriver
33 Brush holder cap
plug — replace them immediately.
sharp blow, been dropped, or otherwise dam-
aged in any way; take it to a qualified service-
man.
tridge; take it to a qualified serviceman when
service or repair is required. Incorrect reas-
sembly may result in a risk of electric shock or
fire.
charger from outlet before attempting any
maintenance or cleaning. Turning off controls
will not reduce this risk.
young children or infirm persons without
supervision.
ensure that they do not play with the battery
charger.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
ture is BELOW 10°C (50°F) or ABOVE 40°C
(104°F).
an engine generator or DC power receptacle.
charger vents.
battery cover when the battery cartridge is not
used.
7